Bedienungsanleitung Trumatic E 2400 (Seite 24 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch)

484023

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Connection of the ducts to the appliance

Remove the two protective gratings from the appliance. Coat

the two pipe pieces LF 18 (1) and the rein-forced ends (2) with

plastic body sealant and insert in the opening of the appliance

(W + U). Secure with two self-tapping screws (3). The duct

connection must be correctly assembled, otherwise splash

water can enter the appliance!

Assembly of the ducts at leadthroughs

Drill two openings 73 mm diameter (W + U). Coat the connec-

tion fittings (4) on the flange with plastic body sealant and screw

on, at opening (U) place the protective grating (5) in between.

Cut the two duct pieces LF 18 (6) to the required length, if

necessary, coat on the inside with plastic body sealant and slide

onto the connection (4). Secure with worm drive hose clip (7).

On the inside, screw on the connection fitting (8) over the

opening (W – can also be screwed together with the connec-

tion fitting on the out-side). With hollow double walls make

sure to seal the intermediate space.

Warm air distribution

Connect duct VR 80 (9) 80 mm diameter and secure with self-

tapping screw (10). The various parts for the duct branching

can also be mounted on the connection fitting (8), for the fur-

ther routing of the ducts VR 72 (72 mm diameter), ÜR (65 mm

diameter) or ZR 18 (49 mm diameter).

In order to prevent overheating, at least one air passage must

always be kept open (swivel nozzle SCW 2). Secure all duct

connections with self-tapping screws. Fasten duct with clamp.

The hot air system is individually designed for each vehicle

model using a modular principle. A wide range of accessories

is available for this purpose (see brochure). Diagrams with op-

timum installation suggestions for hot air systems in all of the

most popular motor home models can be requested free of

charge via the Truma service centre.

Circulating air return

The appliance must be able to intake sufficient circulating

air through the opening (U). If the circulating air return takes

place inside a storage compartment, drill two holes (13) into it,

each measuring 75 mm in diameter or apply an appropriately

sized opening.

Do not obstruct air passages to the appliance!

If the storage compartment is to remain in full use, the return

air can be drawn in through a swivel nozzle SCW 2 and a duct

piece VR 80. For this purpose screw a connection fitting over

the opening (U). Overall length up to the appliance max. 2 m!

Fitting the control panel

When using control panels which are specific to the

vehicle or manufacturer, the electrical connection must

be effected in accordance with Truma interface specifications.

Any modification made to the Truma components pertaining

to this will lead to the cancellation of the guarantee and to the

exclusion of any claims for liability. The installer (manufacturer)

is responsible for providing operating instructions for the user

as well as for the labelling of the control panels!

When selecting the location, take note that the control panels

must not be subjected to any direct radiant heat. Length of

the connection cable 4 m or 10 m.

If installation is only possible behind curtains or in similar

locations with temperature fluctuations, a remote sensor for

the ambient temperature must be used (Accessories).

Installing the control panel with rotary switch

If flush mounting is not possible, Truma will supply an

on-surface frame (1 – part no. 40000-52600) as an

accessory on request.

Drill a hole Ø 55 mm in diameter.

Plug the control panel cable (2) into the control panel (3) and

then fit the rear cover cap (4) as a stress-relieving device.

Push the cable through to the rear and lay it to the electronic

control unit.

Secure the control panel with four screws (5) and fit the cover

frame (6) in place.

Truma offers side parts (7) in eight different colors for

finishing the cover frames (6) in a visually pleasing way.

Please ask your dealer.

Ø 55 mm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trumatic E 2400 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info