Bedienungsanleitung Trumatic E 4000 A (Seite 23 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch)

484609

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Inside installation with wall cowl set

See installation variant Fig. 1 (page 2)

Installation of wall cowl

Install wall cowl (arrow pointing up) on an even surface around

which wind can flow from all sides. Drill an opening of 83 mm

diame ter (pack wood into any hol low spaces in the area of the

cowl opening). Use the en closed rubber seal (8) for sealing. In

the event of structured surfaces coat with plastic body seal-

ant – do not use silicone!

Slide clamp (7) over the ducts prior to passing the exhaust

double duct through the opening.

Slide rubber seal (8 – smooth side toward cowl, sealing

lips toward wall) and clip (4) onto inner section of cowl (9).

Press together end of exhaust duct (1) so that winding touch-

es winding, and slide over O-ring (10) onto the connection

fitting (11 – bend pointing up).

Slide holes of clip (4) onto pins of muff (11 – screw facing

downwards) and screw in place. Slide combustion air intake

duct (5) on the serrated connection fitting (12).

Fasten cowl inner part (9) with 6 self-tapping screws (14),

mount cowl outer part (15) and fasten with 2 screws (16).

Fasten combustion air intake duct with clamp (7), from the

inside, on the connection fitting (12).

Fasten cowl double duct to the wall with at least one clamp

ZRS (17).

Ø 83 mm

TOP OBEN

Double cowl duct connection to the heating

appliance

Slide clip (7) over the pipes. First

compress the exhaust duct (1) so

that the coil windings are pressed

against each other. Slide the

clamp (4) over the exhaust duct (1).

Slide the exhaust duct onto the

connection fitting (2) over the O-ring.

Engage the clamp (4) and screw

tight. Secure the air intake duct (5)

on the connection fitting (6)

with clamp (7).

Inside installation with roof cowl set

See installation variant Fig. 2 (page 2).

Install roof cowl on a surface which is as straight as possible,

with wind flow from all sides. From the appliance to the cowl

it must be possible to have a direct duct route rising over the

entire duct length (max. 2 m)!

Assembling the condensate trap

A condensate trap has to be in-

stalled between the heater and the

double duct to allow condensation

water and rain water to drain away.

The exhaust gas double duct

must not sag – the conden-

sate trap must be the lowest point!

Fully open the clamp (4) and slide

over the O-ring onto the exhaust

gas connection fitting (2). Slide the

exhaust coupling (17) over the

O-ring onto the exhaust gas con-

nection fitting (2 – if the conden-

sate trap is installed on a level

with the heater, the drain (18)

must be facing down). Engage the

clamp (4) and screw tight. Tighten

the drain (18).

Assembling the roof cowl

Drill a hole (8) with diameter 83 mm

(any hollow compartments in the

vicinity of the cowl hole should be

lined with wood). Seal with rubber

seal supplied (22). Coat textured

surfaces with a plastic coachwork

sealing agent (not silicon).

If the roof cowl is relatively thick, first connect the exhaust gas

double duct from the outside onto the cowl. Slide the rubber

seal (22) and clamp (4) onto the inner cowl section (23). First

compress the exhaust duct (1) so that the coil windings are

pressed against each other, then slide over the O-ring onto the

connection fitting (24). Engage the clamp (4) and screw tight.

Slide the air intake duct (5) onto the serrated connection fit-

ting and secure with the black screw (25).

Fasten the cowl section (23) with 6 bolts (26). Mount cowl

roof (27) and secure using 2 bolts (28).

The exhaust vents in the cowl roof must face at right-

angles to the direction of travel.

Always keep the cap (29) on when the heater is not operating.

Double duct connection to the heating

appliance

Press end of exhaust duct (1) together so that winding

touches winding. Slide clamp (4) over exhaust duct (1). Pass

the exhaust duct (1) via the O-ring and fit it to the exhaust

coupling (17). Engage the exhaust duct tightener (4) onto the

exhaust coupling (17) and secure. Take the connection fit-

ting (19) with the wide side over the exhaust duct and slide it

firmly onto the air connection fitting (6) on the heating unit.

Line up the opening in the connection fitting (19) with the

drain (18). Screw in and tighten connection fitting (20).

Slide the air intake duct (5) firmly onto the connection

fitting (19) and fasten with duct clamp (7).

Drill a 10 mm diameter opening in the vehicle floor for the

condensate hose (21). Fasten the condensate hose onto the

connection fitting (20) and pass it through the opening.

Due to the risk of frost in winter, the hose should not

project more than 2 cm below the vehicle floor!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trumatic E 4000 A Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info