Bedienungsanleitung Trumatic E 4000 A (Seite 25 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch)

484609

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Drill two openings with a diameter

of 100 mm. Apply sealing agent

to flange of both connector fit-

tings (41) and bolt to the openings

on the outside. Place the grid (47)

in the recirculating air duct between

the suction connection fitting and

the vehicle wall. Thread LFS wire

clamps (42) onto the air ducts (43).

Slide the air ducts over the heater

connection fittings (44) and the con-

nector fittings (41) and fasten them

with the LFS wire clamps (42). Seal

the joints with silicon paste.

Seal hollow double walls around the

air duct by putting two rolled sheet

metal strips (45) or lengths of pipe

between 97 an 100 mm in diameter

into the openings.

The warm air can be extended

inside the vehicle using LI air duct

(diameter 106 mm). To connect the

air duct, fasten another connec-

tion fitting (41) into the opening.

The two connector fittings can be

bolted together through the wall.

If you wish the warm air to be diffused inside the vehicle, an

air diffuser (46) can be fitted over the warm air duct (W) with

4 bolts.

Do not close off or restrict the opening for the recircu-

lating air duct!

The air diffuser (46) has 2 connections for VR 72 duct (72 mm

diameter), neither of which must be closed off. The protective

metal sheet supplied (48) acts as a heat shield and must be

securely fastened over the air diffuser (46). Stowage protec-

tion can be provided in the form of another protective metal

sheet (49) fastened over the opening for the recirculating air

duct (Accessory, part no. 39010-11500).

The warm air system is designed for each type of vehicle indi-

vidually, on a modular basis. There is an extensive accessories

program available (refer to brochure). Diagrams with optimum

installation suggestions for warm air systems in all of the most

popular motor home models can be requested free of charge

via the Truma service centre.

Fitting the control panel

When using control panels which are specific to the

vehicle or manufacturer, the electrical connection must

be effected in accordance with Truma interface specifications.

Any modification made to the Truma components pertaining

to this will lead to the cancellation of the guarantee and to the

exclusion of any claims for liability. The installer (manufacturer)

is responsible for providing operating instructions for the user

as well as for the labelling of the control panels!

When selecting the location, take note that the control panels

must not be subjected to any direct radiant heat. Length of

the connection cable 4 m or 10 m.

If installation is only possible behind curtains or in similar

locations with temperature fluctuations, a remote sensor for

the ambient temperature must be used (Accessories).

Installing the control panel with rotary switch

If flush mounting is not possible, Truma will supply an

on-surface frame (1 – part no. 40000-52600) as an acces-

sory on request.

Drill a hole 55 mm in diameter.

Plug the control panel cable (2) into

the control panel (3) and then fit the

rear cover cap (4) as a stress-relieving

device.

Push the cable through to the rear and

lay it to the electronic control unit.

Ø 55 mm

Secure the control panel with

four screws (5) and fit the cover

frame (6) in place.

Truma offers side parts (7) in eight different colors for

finishing the cover frames (6) in a visually pleasing way.

Please ask your dealer.

Installing the control panel with slide switch

For existing installation sections.

Remove the cover screen from the installation section.

Plug the control panel cable (10)

into the control panel (8), feed it

to the rear through the installation

section, and lay it to the electronic

control unit.

Push the control panel (8) in until the front face is flush with

the surface.

If there is no installation section present, the control

panel can be fitted with the flush-fitting installation

frame provided.

If flush mounting is not possible, Truma will supply an on-

surface frame (part no. 39050-11600) as an accessory on

request.

Fitting the electronic control unit

Unscrew the cover of the control unit.

The plug on the electronic control unit should only be

withdrawn or plugged in if the supply voltage had been

disconnected beforehand. Pull the plug out straight!

Insert the plug on the control panel

cable (1) as shown in the diagram

onto the red terminal strip of the

control unit.

If a timer switch or a fine sensor is fitted, its plug is to

be inserted on the red terminal strip. If several accessory

components are being used at the same time, connection is

effected via the multiple socket (Accessory).

Secure the lower part with two screws at an easily accessible

location, protected against moisture (must not be heated to

above 65 °C).

Screw the cover of the control unit into place.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trumatic E 4000 A Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info