Bedienungsanleitung Tunturi Go 15 loopband (Seite 9 von 60) (Deutsch, Englisch, Holländisch, Französisch, Finnisch)

615565

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

OWNER’S MANUAL

•

GO RUN 15

• You can set the speed and incline of

each profile bar also manually during

training.

Maintenance

The equipment is safe to use only when

periodically maintained and inspected for

faults and wear.

CAUTION!

Do not attempt any servicing or

adjustment other than those described

in this manual. Any other servicing must

be performed by an authorized service

representative. Check the tightness of

all fixing screws once a year. Do not

overtighten.

CLEANING AND LUBRICATING THE

TREADMILL

FAILURE TO LUBRICATE YOUR

TREADMILL MAY INVALIDATE THE

PRODUCT’S WARRANTY!

Wipe the treadmill surfaces, especially

the handlebars and console from dust

with a damp cloth or towel. Do not use

solvents. Use a small vacuum nozzle

to carefully vacuum around all visible

components (belt, running deck, side

rails etc.). Also keep the area near

the treadmill clean. While in use,

the treadmill gathers dust that may

cause problems in the operation of the

equipment. In average domestic use (a

maximum of 60 minutes a day),

you should check the lubrication once

a month

However, lubricate the belt only if

needed. In more demanding use, the

lubrication needs be checked at shorter

intervals. This is best done before you

begin a training session. Check the

lubrication as follows:

• Ensure the treadmill is powered off!

Step on the treadmill belt .and stand

steadily where you normally run on

the belt.

• 2. Take hold of the horizontal

handlebar and push the belt with

your feet so that it slides back and

forth. The belt should move softly and

evenly, without a sound.

• 3. If you notice jerky movement or

if the belt will not slide check for

lubrication by sliding your hand under

the belt.

Lubricate the running deck according

to the following instructions:

• Attach the nozzle of the lubrication

tube to the T-Lube S container.

• Lift the running deck and lock it.

• Position the nozzle between the belt

and the board. Try to reach the spray

as far into the center of the running

deck as possible.

• Spray the lubricant for 2-3 seconds.

• Lower the running deck into its

normal position. Use treadmill for

your training session. Or allow the

treadmill to run for at least 5 minutes.

NOTE!

Lubricate your treadmill only with T-Lube

S silicon lubricant. Contact your local

Tunturi distributor for further supplies

of T-Lube or further information on

lubrication and maintenance.

ALIGNING THE RUNNING BELT

Monitor belt tracking during exercise and

make adjustments as needed. The belt

should run in the center of the treadmill.

Alignment is not usually needed,

provided

• The treadmill is placed on an even,

solid and horizontal surface and the

belt is correctly tensioned

• The alignment of the belt is correct

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tunturi Go 15 loopband Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info