550273
38
Zoom out
Zoom in
Vorherige Seite
1/54
Nächste Seite
Alternate displays during a dive with two gases
All displays time out after 5 seconds and the default display is shown again.
(Only exception is the temperature, screen 2 below.)
1
The default display shows the predictive decompression prognosis, which assumes the diver will
switch to the deco gas at the specified switch depth. In the bottom left corner the temperature is
displayed unless the current depth is 1m/3ft shallower than the max depth, in which case the max
depth is displayed.
2
Upon pressing the right button, the temperature and the current O
2
% are shown in the lower row.
O
2
% will time out after 5 sec while the temperature remains.
3
Upon pressing the right button, "GAS 1" or "GAS d" appears in the middle row to indicate the cur
-
rently active gas and the MOD appears in the bottom left corner. "GAS 1" or "GAS d" will time out
after 5 seconds unless the right button is pressed again.
4
In case that gas 1 is the active gas, pressing the right button one more time shows O
2
% of gas 1 in
the bottom right corner and the decompression information in case the deco gas is not used (decom-
pression information relative to gas 1 only). This is the calculation that Aladin would switch to in case,
having reached the switch depth, the diver did not confirm the switch. The decompression information
and the O
2
% blink.
5
If an MB level greater than L0 is active, pressing the right button one more time shows the predictive
decompression information and in the bottom left corner the currently active MB level.
6
Pressing the right button again shows the predictive decompression information relative to L0 togeth
-
er with the L0 symbol at the bottom left.
7
One more right button push shows the decompression information relative to L0 if only gas 1 is used,
with the decompression information and the O
2
% of gas 1 blinking.
8
Upon pressing the right button again, the time of day appears in the middle row.
The time to reset the
O
2
% mix to air can be set with SmartTRAK between
1 hour and 48 hours or to "no reset" (default).
After the reset, the oxygen fraction of gas 1 is set to 21% and gas D is set to
"– – O
2
%" (single gas dive).
Switching between single-gas and two-gas diving
If gas D is not going to be used during the next dive you can either set it to
"– O
2
%" (->37, point 2) or you can turn off the deco gas option in SET 1.
When you turn off the deco gas option in SET 1, the setting in the GAS D O
2
menu remains but Aladin calculates the dive using gas 1 only.
If the deco gas option is turned off, the GAS D O
2
menu will display OFF in the
lower left corner (instead of an MOD) and the ppO
2
setting will not appear.
VI Diving with two gas mixtures
Predictive decompression prognosis
The calculation of decompression data is based on the assumption that the change of gas mixture will be
performed at the previously selected switch depth (MOD gas D). If a diver ignores the required change or
changes the mixture belatedly, Aladin will readjust the decompression calculation accordingly. In case of
an ignored switch the dive computer will then base its calculations on the assumption that the diver will
ascend to the surface with gas 1.
WARNING
Functions during a dive with two gas mixtures
Diving with more than one gas mixture represents a much higher risk than
diving with a single mixture, and mistakes by the diver may lead to serious
injury or death.
During dives with several gas mixtures, always make sure you are breathing from the tank you intended
to breath from. Mark all your tanks and regulators, so they can under no circumstances be mixed up!
Before every dive and after changing a tank, make sure that each gas mixture is set to the correct value
for the corresponding tank.
VI UWATEC Aladin TEC 2G
38
38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für UWATEC Aladin TEC 2G wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von UWATEC Aladin TEC 2G

UWATEC Aladin TEC 2G Bedienungsanleitung - Deutsch - 54 seiten

UWATEC Aladin TEC 2G Bedienungsanleitung - Holländisch - 54 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info