611085
9
Zoom out
Zoom in
Vorherige Seite
1/20
Nächste Seite
9
7.4 Remove the vent connection unit.
Detach the vent connection unit from the top of the
appliance case by removing the screw at front. Slide
the vent connection unit back and lift clear (see
fig.10).
7.5 Fit the canopy shield.
Attach the canopy shield to the convection air outlet
aperture using the three thread cutting screws
supplied in the fire front pack (see figure 11).
Take care not to damage the vent safety shut-
off switch mounted at the top left of the
convection air outlet
7.6 “Visage” front only
Fit the two surround securing brackets to the
convection box side flanges with the screws
supplied. Be aware of the different orientation of
the brackets at left and right sides - See figure 11A.
8. GAS SUPPLY LINE
INSTALLATION
8.1 Gas connection to the appliance is 3/8”NPT.
8.2 Use only new black iron or steel pipes or copper
tubing if acceptable - check local codes. Note that in
USA copper tubing must be internally tinned for protection
against sulfur compounds.
8.3 Unions in gas lines should be of ground joint type.
8.4 The gas supply line must be sized and installed to
provide a supply of gas sufficient to meet the
maximum demand of the appliance without undue
loss of pressure.
8.5 Sealants used must be resistant to the action of all
gas constituents including LP gas. Sealants should be
applied lightly to male threads to ensure excess
sealant does not enter gas lines.
8.6 The supply line should include a manual shut-off
valve to allow the appliance to be disconnected for
servicing.
8.7 A plugged 1/8”NPT tapping must be installed in the
line. The tapping must be accessible for test gauge
connection and be immediately upstream of the gas
supply connection to the appliance.
8.8 Before the appliance is fitted into the fireplace
opening the supply line must be extended so that it
will project through the opening at back of the
convection box.
The supply pipe route to the gas valve / connector is
shown in figure 12.
Fig12 Supply pipe routing
Fig10 Vent connector removal
Fig. 11 Canopy shield attachment
Left side Right side
Fig. 11A “Visage” surround securing brackets
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Valor 722AN wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info