Bedienungsanleitung Velodyne SMS-1 (Seite 15 von 49) (Englisch)

567863

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

www.velodyne.com

Digital Drive SMS-1 User’s Manual - 9

INSTALLATION – STEP-BY-STEP

To ensure a quick and awless installation of your Velodyne Digital Drive SMS-1, follow these setup instructions.

SMS-1 Cable Connections

Make all necessary cable connections between the applicable SMS-1 connector port and your particular

home electronics equipment in the following order:

1. Insert the detachable power supply into the power interface port on the rear panel of your SMS-1.

Plug the male end of the cord into a convenient wall outlet.

2. Provide signal to your SMS-1 through one or more of the following connections (refer to your

receiver/processor owner’s manual for available inputs to the SMS-1):

a. LFE INPUT (RCA, the RED jack at location 17 on Figure 1) – This is the most common input

cable connection. Make a connection between this input and the LFE output of your receiver

or processor; OR

b. LFE INPUT (XLR, location 7 on Figure 1) – Make a connection between this input and the

balanced LFE outputs of your receiver or processor; OR

c. INPUT, LEFT and RIGHT (location 17 on Figure 2)– Make a connection between these inputs

and the stereo outputs of your receiver or processor; OR

d. SPEAKER-LEVEL INPUT (location 18 on Figure 2) - Make a connection between these inputs

and the left and right speaker connections on your receiver or processor. Make this connection

by inserting speaker wire into the correct terminals of the terminal block.

3. Establish the return line-level connection (optional). Connect to a pre-amplier’s main outputs and

return them to your amplier inputs. When installed in this fashion, your satellite speakers will be

crossed over at 80Hz, which removes the lower bass from your amplier and speakers, enabling

them to do a better job reproducing high frequencies. By utilizing this method, you will have a bi-

amplied system, gaining improved power and headroom for your system.

NOTE: To bypass the 80Hz crossover described in step 3, use the THRU output jacks instead of the OUTPUT

jacks.

A word about SMS-1 outputs

The Velodyne SMS-1 is designed to operate using the full range audio signal for input when using the digital

built-in crossover. Most processors/receivers have a “subwoofer out” or LFE jack that is internally ltered and

designed to be used with a conventional amplier and speaker. In some rare cases, combining both an external

crossover and the one internal to the SMS-1 may result in low output and increased noise. In these installations

you may need to bypass the internal crossover in either the processor or Velodyne SMS-1. In some installations,

simply setting one crossover to a higher frequency (such as 120Hz) will restore maximum performance. To

bypass the SMS-1’s internal crossover when the unit is being fed a low pass signal from another crossover, refer

to the SETUP instructions at step 14, below.

Note: If not using an external crossover, you should use the built-in crossover for optimal performance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Velodyne SMS-1 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info