567863
17
Zoom out
Zoom in
Vorherige Seite
1/49
Nächste Seite
www.velodyne.com
Digital Drive SMS-1 User’s Manual - 11
Choose one SMS-1 for all the connections described below (we’ll call this the “master”), and then connect an
RCA jack from the THRU RCA jacks of the “primary” to the Input jacks of the “slave.” You will also need to
obtain a “Mouse Extension” serial cable (available at any computer store, from your Authorized Velodyne dealer,
or from Velodyne directly) and connect the RS232 OUT port of the primary SMS-1 to the RS-232 IN port of the
secondary SMS-1. Then, all runtime commands directed at the primary SMS-1 (such as select preset, volume,
etc.) will be communicated to the secondary SMS-1 automatically through the serial cable. If you have more
than two SMS-1s in your setup, simply continue the daisy chain from the secondary SMS-1 to the next SMS-1
in the line (using both RCA and serial connections) and so on.
NOTE: When an SMS-1 detects an incoming RS-232 command, it reverts to “Slave Mode.” This means that
the SMS-1 will no longer accept IR commands. To reestablish normal operations, disconnect the RS-232 cable
and power cycle the unit.
Note that the daisy chain connection ONLY allows the woofers to communicate basic “run-time” commands
such as volume and preset. We recommend the following sequence when setting up daisy-chained SMS-1s.
1. First, connect only the master SMS-1/subwoofer(s) to the system. Do not connect the thru or serial
cables at this time.
2. Establish the crossover, phase, and other settings EXCEPT the EQ on the master SMS- 1/subwoofer(s)
(see setup steps 1 – 17 below). Note the low pass crossover, phase and polarity settings, then save.
3. Connect the video out of the slave SMS-1/subwoofer(s), go to the settings screen, establish the low
pass crossover, slope, phase, polarity, and night mode settings from the master SMS-1, then save
settings.
4. Connect the microphone to the slave SMS-1/subwoofer(s) and use the “self-EQ” feature (described
below) to establish room EQ for that SMS-1.
5. Repeat steps 3 and 4 for each slave SMS-1/subwoofer(s) in your system.
6. Reconnect the video out to the master SMS-1/subwoofer(s), and reconnect the thru and serial cables so
that the master and slave SMS-1(s) are daisy chained.
7. EQ the primary SMS-1/subwoofer(s) (see steps 8-25). Self-EQ is NOT recommended for the primary
SMS-1/subwoofer(s).
8. Setup is complete!
17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Velodyne SMS-1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info