Bedienungsanleitung Velodyne SMS-1 (Seite 16 von 49) (Englisch)

567863

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

www.velodyne.com

10 - Digital Drive SMS-1 User’s Manual

4. Connect the audio/video cables between your SMS-1 (EQ OUTPUT VIDEO/LEFT/RIGHT – yellow, white,

and red respectively) and your electronics (receiver, processor, TV, etc.). Insert the color-coded cable

plugs into the correct EQ OUTPUT receptacle – the yellow plug into the VIDEO jack, the white plug

into the LEFT jack, and the red plug into the RIGHT jack. The opposite ends of the cables should

be connected to your receiver/processor. The yellow VIDEO cable goes to an available composite

video input (e.g. aux), and the white/red AUDIO (L&R) cables go to a corresponding audio input. As an

alternative to composite video, you may want to use S-video (S-video connector not included). Connect

the S-video from the SMS-1 to an S-video compatible input on either your processor or TV. Consult your

receiver/processor and/or TV owner’s manual for more information.

5. Connect your subwoofer(s) to the SMS-1 using the XLR connector or LFE out RCA connector.

6. Defeat the crossover on your subwoofer(s) (if possible) and set its volume to the middle setting.

NOTE: Make sure the audio output goes into your AUDIO system, not your TV! The SMS-1 will generate test

tones used to match the SMS-1 to your satellites and to correct for room anomalies that need to be played by

your main audio system.

7. Insert the XLR microphone cable’s 3-pin male plug into the MIC INPUT jack (location 7 on Figure 2) on

the front or back panel of the SMS-1.

8. Slide the microphone (male connector end rst) down through the open, circular sleeve of the tabletop

microphone stand. Position this assembly at a desired listening position.

NOTE: The Digital Drive Accessory Kit includes a microphone stand adapter (1/2”-27 thread) for use with

professional mounting stands. Be sure to rst remove the inner thread piece (3/8”-16) before using.

9. Connect the XLR microphone cable’s female jack end with the male connector end of the microphone.

10. Sheath the microphone pickup with the foam windscreen cover as a protection against dirt and airborne

contaminants.

A Word About Interconnect Cables

When installing your new Velodyne SMS-1 using the line level connections, you should always use shielded

phono cables. There are many quality cables available today, most any of which will work perfectly well. We

do recommend that you keep the length of cable as short as possible to avoid any potential noise problems..

A Word About Connecting More Than One Subwoofer

Note that your SMS-1 can control up to three subwoofers. Each of the three subwoofers will receive the same

conditioned signal from the SMS-1. If you wish to run more then three subwoofers, or wish to individually

customize the signal to dierent subwoofers, you will need more than one SMS-1 connected in a “daisy-chain”

conguration. This section describes setup in a daisy-chain conguration.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Velodyne SMS-1 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info