Bedienungsanleitung Venga VG SIS 2 (Seite 11 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

488163

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite



Copies of the I/B. Please reproduce them without any

changes except under special instruction from Team

International BELGIUM. The pages must be reproduced

and folded in order to obtain a booklet A5 (+/- 148.5 mm

width x 210 mm height). When folding, make sure you

keep the good numbering when you turn the pages of

the I/B. Don’t change the page numbering. Keep the

language integrity.

VG SIS 2 - 101214

Assembly page 11/56

Fax +32 2 359 95 50

 Do not use the iron if it has fallen, if it shows any visible signs of damage or if it leaks.

 When you place the iron on its support (if available with the model), make sure that the

surface on which you put it is stable.

 Proceed the same way if the water tank stops working or is damaged. To avoid the risk of

electric shock, do not disassemble the iron or steam tank, take it to a qualified technician

for examination and repair. Incorrect re-assembly can cause a risk of electric shock when

the iron or steam tank is used.

 Fully unwind the main cord and supply hose before starting to iron.

 The power switch should always be put in position “0” before plugging or unplugging the

power cord from outlet.

 Unplug the appliance and allow the iron and the water tank to cool down before

cleaning or storing them and for pressurized steam iron station (depending on the model)

before opening, filling or emptying the water tank.

 FOR PRESSURIZED STEAM IRONING STATION (DEPENDING ON THE MODEL), NEVER OPEN THE

CAP OF THE STEAM TANK WHILE THE APPLIANCE IS CONNECTED TO THE MAINS WALL SOCKET

AND ESPECIALLY WHEN STEAM IS BEING PRODUCED.

(*)

Competent qualified service: after sales department of the producer or importer or any

person who is qualified, approved and competent to perform this kind of repairs in order to

avoid all danger. In any case you should return the appliance to this service.

BEFORE THE FIRST USE

• We recommend cleaning the iron before the first use as follows: fill the water tank, put the

temperature dial on position “LINEN” and the steam regulator on MAX and let the iron

heat for 10 minutes. When the temperature has been reached, take the iron from the

base, hold it vertically and keep the steam button pressed for 30 seconds, then wait 30

seconds and repeat this cycle twice.

• Switch off the appliance (switch in position “0”), unplug it and let it cool down sufficiently,

then clean the soleplate with a damp cloth.

STEAM IRON: PRECAUTION FOR USE AND TEMPERATURES

• Always check first if a label with ironing instructions is attached to the article that needs to

be ironed. Follow these ironing instructions in all cases.

• If ironing instructions are missing but you know the kind of fabric, then see the table for

recommended ironing temperatures.

Kind of textile Temperature dial Steam ironing

Nylon

Synthetic (e.g. acetate,

acrylic, viscose,

polyamide, polyester, …)

Silk

MIN







Wool







YES

Cotton

Linen







MAX

YES

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Venga VG SIS 2 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info