Bedienungsanleitung VibroShaper E380 (Seite 17 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

703857

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Automatic mode: Here, the device follows a predeﬁned exercise programme, but still allows the tempo and length to be set

manually. When using automatic mode, follow these instructions:

1. Plug the Vibroshaper into a power socket and press the power switch (3) so that it is in the ON position.

2. Press the “ON” button on the control panel (15) or the button on the remote control.

3. There are three different exercise programmes (P1, P2 and P3) available. Press button (16) on the control panel repeatedly or the

button on the remote control repeatedly until the programme you want appears on the programme display (8).

4. The next chart shows the exercise tempo of each programme depending on the length:

TIME TEMPO FOR EVERY PROGRAMME

(minutes)

P1 P1 P3

9 16 20 10

8 18 40 44

7 28 60 99

6 38 80 33

5 48 99 99

4 58 40 22

3 48 99 99

2 38 40 11

1 28 99 99

BEGINNERS MODERATELY ADVANCED ADVANCED

5. Once you’ve selected your chosen programme, start the exercise by pressing (17) on the control panel or on the

remote control.

6. To stop the device at any time, press the button (18) on the control panel or the

button on the remote control. Once you’ve

completed the exercise, turn the device off by pressing (15) on the control panel or the button

on the remote control.

CLEANING AND MAINTENANCE

• Before cleaning your Vibroshaper, you must make sure that the power switch is in the OFF position and that the cable has been

unplugged from the power socket.

• You can use a clean, dry broom or brush to remove dust from the device.

• The standing area can be cleaned with a damp cloth.

• Do not use corrosive agents to clean the device, because these could damage it.

• Clean the remote control with clean cloth.

• If the device is not being used for an extended period of time, put it back in its box and store it in a cool, dry place. You should

also take the batteries out of the remote control.

• If the device appears to have a defect, follow the instructions in the Troubleshooting section. If the problem persists,

please contact our customer service team.

TROUBLESHOOTING

PROBLEM CAUSE SOLUTION

The device is not running.

The cable is not plugged

into a socket.

Plug the cable into a socket.

The power switch is in the OFF position. Put the power switch in the ON position.

The remote control

is not working.

The batteries are weak. Change the batteries.

The remote control is too far

away from the device’s infrared sensor.

The infrared signal’s range is two metres.

The device suddenly

stopped running.

The end of the programmed exercise

period has been reached.

Reset the exercise period.

The device isn’t moving.

The device has been given too many com-

mands and is not able to fulﬁl them all.

Turn off the device, wait one

minute and turn it on again.

The remote control can’t

be used to stop the device

while the device is running.

The batteries are weak.

Change the batteries.

The On/Off

button has been pressed.

Press the Start/Stop

button.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

VibroShaper E380 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von VibroShaper E380

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info