Bedienungsanleitung Victron EasySolar-II 48 3000 35-32 MPPT 250 70 GX (Seite 6 von 146) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch)

785554

Zoom out

Zoom in

Vorherige Seite

1/146

Nächste Seite

4.2 Features specific on-grid and off-grid systems combined with PV

4.2.1 External current transformer (optional)

When used in a grid-parallel topology the internal current transformer cannot measure the current to or from the mains.

In this case an external current transformer has to be used. See appendix A. Contact your Victron Distributor for further

information about this installation type.

4.2.2 Frequency shift

When solar inverters are connected to the AC-output of the product, excess solar energy is used to recharge the

batteries. Once the absorption voltage is reached, charge current will reduce and excess energy will be fed back into the

mains. If the mains is not available, the product will slightly increase the AC frequency to reduce the output of the solar

inverter.

4.2.3 Built-in Battery Monitor

The ideal solution when the product is part of a hybrid system (diesel generator, inverter/chargers, storage battery, and

alternative energy). The built-in battery monitor can be set to start and stop the generator:

• Start at a preset % discharge level, and/or

• start (with a preset delay) at a preset battery voltage, and/or

• start (with a preset delay) at a preset load level.

• Stop at a preset battery voltage, or

• stop (with a preset delay) after the bulk charge phase has been completed, and/or

• stop (with a preset delay) at a preset load level.

4.2.4 Autonomous operation when the grid fails

Houses or buildings with solar panels or a combined micro-scale heating and power plant or other sustainable energy

sources have a potential autonomous energy supply which can be used for powering essential equipment (central

heating pumps, refrigerators, deep freeze units, Internet connections, etc.) during a power failure. A problem is however

that grid connected sustainable energy sources drop out as soon as the grid fails. With the product and batteries, this

problem can be solved: the product can replace the grid during a power failure. When the sustainable energy

sources produce more power than needed, the product will use the surplus to charge the batteries; in the event of a

shortfall, the product will supply additional power from the battery

4.3 Battery charger

4.3.1 Lead-acid batteries

Adaptive 4-stage charge algorithm: bulk – absorption – float – storage

The microprocessor-driven adaptive battery management system can be adjusted for various types of batteries. The

adaptive function automatically adapts the charging process to battery use.

The right amount of charge: variable absorption time

In the event of slight battery discharge, absorption is kept short to prevent overcharging and excessive gas formation.

After deep discharging, the absorption time is automatically extended in order to fully charge the battery.

Preventing damage due to excessive gassing: the BatterySafe mode

If, in order to quickly charge a battery, a high charge current in combination with a high absorption voltage has been

chosen, damage due to excessive gassing will be prevented by automatically limiting the rate of voltage increase once

the gassing voltage has been reached.

Less maintenance and aging when the battery is not in use: the Storage mode

The Storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the Storage

mode float voltage is reduced to 2,2V/cell (13,2V for 12V battery) to minimise gassing and corrosion of the positive

plates. Once a week the voltage is raised back to the absorption level to 'equalize' the battery. This feature prevents

stratification of the electrolyte and sulphation, a major cause of early battery failure.

Battery voltage sense: the correct charge voltage

Voltage loss due to cable resistance can be compensated by using the voltage sense facility to measure voltage directly

on the DC bus or on the battery terminals.

Battery voltage and temperature compensation

The temperature sensor (supplied with the product) serves to reduce charging voltage when battery temperature rises.

This is particularly important for maintenance-free batteries, which could otherwise dry out by overcharging.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Victron EasySolar-II 48 3000 35-32 MPPT 250 70 GX Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info