Bedienungsanleitung Visonic Powermaster-360 (Seite 50 von 96) (Englisch)

769323

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

50 D-307500 PowerMaster 360 Installer's Guide

Enter the WL DEVICES menu, select the type of test you require to perform (see guidance above and in section 4.8.1),

then refer to the table below which provides you with detailed explanations for each option.

Option

Instructions

TEST ALL DEVICES

You can test all wall-mounted devices automatically, one after the other, after which the

installer tests the other devices in the following order: vanishing magnetic contact

devices, keyfobs and then panic buttons.

While in TEST ALL DEVICES, press to initiate the test. The following screen will

appear: TESTING Xxx NNN, where Xxx indicates the type of device and NNN indicates the

number of enrolled devices in the panel that have not been tested yet. This number automatically

drops one count for every tested device.

Pressing any key during the testing process will open the following options:

1. Press to jump to the next device group. For example, from wall-mounted devices to

keyfobs.

2. Press to continue the testing process

3. Press to exit the test process.

When all wall-mounted devices have completed the test procedure, you can test vanishing

magnetic contact devices.

While in the vanishing test process, indicated by the corresponding display, for example,

TEST VANISH NNN, momentarily open the door or window.

When all vanishing magnetic contact devices have been tested, you can test keyfobs.

While in the keyfobs test process, indicated by the corresponding display, for example,

TEST KEYFOBS NN, press any key of the selected device to initiate the test.

When all keyfobs have been tested, you can test panic buttons.

While in the panic button test process, indicated by the corresponding display, for example,

TEST PANIC BT. NN, press a button on the pendant.

At the end of the test process, the panel will present the following: SHOW ALL DEVICES.

Press to view devices' status.

Note: Refer to SHOW ALL DEVICES section below for further information on device status.

TEST ONE DEVICE

CONTACT SENSORS

MOTION SENSORS

GLASSBREAK SENS.

SHOCK SENSORS

SMOKE SENSORS

CO SENSORS

GAS SENSORS

FLOOD SENSORS

TEMPERATURE SENS.

KEYFOBS

PANIC BUTTONS

KEYPADS

SIRENS

REPEATERS

You can select a specific device group you require to test, for example, Motion Sensors.

Press to enter the TEST ONE DEVICE sub menu and use to scroll through the

device families. Press to enter the <device family> sub menu, for example:

MOTION SENSORS.

Note: If there is no enrolled device,

NO EXISTING DEV.

will be displayed.

The following screens will then appear: Xxx:<device name>  <location>, where Xxx

indicates the device number. You can now select a specific device.

Press to test the selected device. The following screen will appear: TESTING Xxx 001.

While in the keyfobs, panic button or vanishing magnetic contact test process, indicated

by the corresponding display, for example, Xxx ACTIVATE NOW, press any key of the

selected keyfob or panic buttons, or momentarily open the door or window, to initiate the

test.

At the end of the test process, the panel will present the devices' status:

Xxx: 24hr: <status>1  Xxx: NOW: <status>1.

Note: Refer to the SHOW ALL DEVICES section for further information on device status.

SHOW ALL DEVICES

You can view the devices status.

Note: This option is available only after testing process was done.

Press to view the devices' status.

The following screens will appear: Xxx: 24hr: <status>1  Xxx: NOW: <status>1

Use to scroll between the device's families.

The signal strength indications are as follows: STRONG; GOOD; POOR; 1-WAY (the device operates in 1-way mode

or, the NOW communication test failed); NOT TST (results are shown without any performed test); NOT NET [device

is not networked (not fully enrolled)]; NONE (keyfob 24Hr result); or EARLY (result of the last 24Hrs without

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Visonic Powermaster-360 Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info