Bedienungsanleitung Visonic Powermaster-360 (Seite 57 von 96) (Englisch)

769323

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

D-307500 PowerMaster 360 Installer's Guide 57

4.14 Operation mode

Note: The Operation Mode feature is applicable only in specific PowerMaster-360 variants.

4.14.1 General guidance – Operation mode menu

This mode allows you to select an operation mode for the control panel according to specific compliance standards.

Each operation mode has its own configuration.

4.14.2 Select setting

To select the desired operation mode, proceed as follows:

Step 1

Step 2

Step 3

Step 4

Select 13:OPERATION MOD menu

Enter 01:SELECT MODE

Select NORMAL, EN-50131,

DD243, BS8243, INCERT or CP01



13:OPERATION MOD

01 SELECT MODE

NORMAL 

 to Step 2

Note: If you select Normal / EN-50131 / INCERT, the control panel will operate according to OTHERS setup configuration

(see section 4.14.6).

4.14.3 BS8243 Setup

13:OPERATION MOD  02:BS8243 SETUP

Enter the 02:BS8243 SETUP menu to configure its settings.

Option

Configuration Instructions

01:DISARM OPTION

Define when it is possible to disarm the system:

entry/BS devs (default) – By keypad after the entry delay has expired and if an alarm occurred

in the system. By keyfob or KP-160 PG2 at all times.

entry/all devs - During entry delay, when the system is armed AWAY, by all devices. When

not in entry delay by keyfob or KP-160 PG2 only.

entry/DD devs - During entry delay, when the system is armed AWAY, by using the keyfob or

KP-160 PG2. Keypads cannot disarm at all.

anytime/all dev – At any time and by all devices.

02:ENTRY ALARM

Define whether the system will report a confirmed alarm during an entry delay (see CONFIRM

ALARM below).

BS8243 (default) – An alarm initiated by another detector during the entry delay is regarded as

a confirmed alarm. An additional 30 seconds delay is added to the entry delay for reporting the

event (does not affect the Abort Time, see section 4.5.4).

BS8243 no cnfrm - The panel will not send any confirmed alarm once a delay zone has been

activated, until the control panel is disarmed.

DD243 - An alarm initiated by another detector during the entry delay is not regarded as a

confirmed alarm.

normal mode - The control panel will report a confirmed alarm for the second alarm that is

triggered from a different zone within the confirmation time. There are no alarm restrictions

during entry delay or for the delay zone.

03:END EXIT MODE

Define how the exit delay is terminated or restarted according to the following options:

door/fob only (default) - When the door is closed, or by pressing the AUX button on the

keyfob1, whichever first.

restart>reentry - Exit delay restarts when the door is reopened during exit delay. The restart

occurs once only. Restarting the exit delay is helpful if the user re-enters immediately after

going out to retrieve an item that was left behind.

door/fob/timer - When the door is closed, by pressing the AUX button on the keyfob1, or when

the exit delay has expired, whichever first.

fob/timer - By pressing the AUX button on the keyfob1, or when the exit delay has expired,

whichever first.

Applies only when the keyfob is defined as skip exit delay (for further details, see the keyfob's User's Guide)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Visonic Powermaster-360 Seite 57

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info