Bedienungsanleitung Vonroc CR504AC (Seite 8 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch)

819185

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

WWW.VONROC.COM

4. OPERATION

You must fully assemble the compressor

before using it for the ﬁrst time.

Long supply cables, extensions, cable reels

etc cause a drop in voltage and can impede

motor start-up. Do not use cables longer

than 10m. Vonroc advises to use a longer

air hose instead.

It can be more difﬁcult to start-up the motor

during conditions of temperatures below 5°C.

The head/cylinder/transmission pipe

assembly may reach high temperatures, so

take care when working close to these

parts and do not touch them to avoid burns.

Starting up (Fig. A)

1. Check whether the mains voltage corresponds

to that indicated on the electrical speciﬁcation

plate.

2. Push the ON/OFF switch (2) into the position ‘O’

to switch the compressor off.

3. Put the plug in the plug socket.

4. Pull the ON/OFF switch (2) into the position ‘I’

to switch the compressor on.

5. The operation of the compressor is fully

automatic. The pressure switch (3) will stop

the compressor when the maximum value has

been reached and start it up when the pressure

drops below the minimum value. The pressure

switch (3) is set at the factory. Normally the

difference in pressure is approx. 2 Bar/29 psi

between the maximum and the minimum value.

The compressor will stop when it reaches 8

Bar (116 psi) (this is the maximum operating

pressure) and will start up automatically when

the pressure within the tank has dropped to 6

Bar (87 psi).

Connecting the air hose and tool (Fig. A)

1. Turn the pressure regulator (4) turning knob

anti-clockwise till pressure is fully released.

2. Insert the connector of the air hose (not inclu-

ded) into the quick coupler (5) on the compres-

sor. When pushing, the connector clicks into

place to secure the air hose.

3. Connect the air tool (not included) you want to

use to the quick coupler of the air hose.

4. Turn the pressure regulator (4) turning knob

clockwise, till the pressure gauge (6) shows the

pressure level you need.

5. Your air tool is now ready to use.

Disconnecting the air hose and tool (Fig. A)

When releasing the quick coupler, be sure

to hold the hose to protect yourself from

injury from the rebounding hose.

1. Turn the pressure regulator (4) turning knob

anti-clockwise till pressure is fully released.

2. Reduce the pressure by activating the air tool

(not included).

3. Pull back the sleeve on the air hose quick

coupler and remove your air tool.

4. Pull back the sleeve on the quick coupler (5)

and remove the hose.

Reading the pressure (Fig. A)

The compressor has two pressure gauges (6,7).

The tank pressure can be read on the pressure

gauge (7) and the operating pressure (regulated

pressure) can be read on the pressure gauge (6).

The black scale indicates the pressure in bar and

the red scale indicates the pressure in PSI.

Adjusting the operating pressure (Fig. A)

It is not always necessary to use the

maximum operating pressure. The air tools

often require less pressure. Always check

the correct operating pressure of the tool

you intend to use.

With regard to compressors supplied with a

pressure regulator (4) it is necessary to set the

operating pressure properly. It is possible to set the

operating pressure by using the turning knob on

the pressure regulator(4):

• By turning clockwise, the operating pressure

will be increased.

• By turning anti-clockwise, the operating pressu-

re will be reduced.

Note: when not connecting an air tool while adjus-

ting the pressure, it might occur the pressure gauge

(6) is not reacting accurately on the pressure drop.

Overload switch (Fig. A)

The motor is ﬁtted with an overload switch (14). If

the compressor overloads, the overload switch (14)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc CR504AC Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info