Bedienungsanleitung Vonroc CR504AC (Seite 9 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch)

819185

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

WWW.VONROC.COM

switches the equipment off automatically to protect

the compressor from overheating. If the overload

switch (14) triggers, switch off the compressor

using the ON/OFF switch (2) and wait until the

compressor cools down. Then press the overload

switch (14) and restart the compressor.

Finish operation (Fig. A, C)

Do not touch the compressor unless its

power has been cut off for at least 10

minutes.

When there is the risk of frost or if you do

not use your compressor for a long time,

please properly store your compressor.

1. Check that the ON/OFF switch (2) is in the ‘O’

position.

2. Remove the mains plug from the mains.

3. Reduce the pressure in the tank till approxima-

tely 2 bar by connecting and activating an air

tool.

4. Then slowly turn the drain cock (11) on the lo-

wer side of the tank open. The water in the tank

(15) will now leak out of the tank (15).

5. Take care when compressed air is in the tank

(15) because the water can come out with some

force. Recommended pressure max. 1-2 Bar.

6. Remove the air tool and hose.

7. Clean and store the device (see ‘Maintenance’).

5. MAINTENANCE

Before cleaning and maintenance, always

switch off the machine and remove the

mains plug from the mains.

Do not touch the compressor unless its

power has been cut off for at least 10

minutes. Risk of burns!

Always depressurize the tank before carrying

out any cleaning and maintenance work.

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that the

ventilation openings are free of dust and dirt. Re-

move very persistent dirt using a soft cloth moiste-

ned with soapsuds. Do not use any solvents such

as gasoline, alcohol, ammonia, etc. Chemicals such

as these will damage the synthetic components.

Drain the tank (Fig. C)

Check the pressure tank for signs of rust

and damage each time before using. Do not

use the compressor with a damaged or

rusty pressure vessel.

Compressing air will cause water in the tank. Regu-

larly drain the water from the tank to prevent tank

corrosion. It depends on the humidity, but advice is

after each use.

1. Reduce the pressure in the tank till approximate-

ly 2 bar by connecting and activating an air tool.

2. Then slowly turn the drain cock (11) on the lo-

wer side of the tank open. The water in the tank

will now leak out of the tank.

3. Take care when compressed air is in the tank

because the water can come out with some

force. Recommended pressure max. 1-2 Bar.

Clean the air ﬁlter (Fig. D)

It is recommended to disassemble the

suction ﬁlter every 50 operating hours and

to clean the ﬁlter element by blowing it with

compressed air.

It is recommended that the ﬁlter element is

replaced at least once a year if the

compressor is working in a clean environ-

ment; more often if the environment in

which the compressor is situated is dusty. A

clogged intake ﬁlter will decrease the

compressor’s performance dramatically.

1. Open the halves of the air ﬁlter housing. Use

compressed air at low pressure (approx. 3 bar)

to blow out all the parts of the ﬁlter

2. Assemble the ﬁlter in reverse order.

STORAGE AND FROST PROTECTION

The compressor and accessories that are not

completely drained can be destroyed by frost. Com-

pletely drain the compressor and accessories and

protect them against frost. Keep this appliance in

well-ventilated dry premises with temperature not

going below +5°C. When not in use, keep this appli-

ance stored in a safe place out of reach of children.

Malfunction

Should the machine fail to function correctly, a

number of possible causes and the appropriate

solutions are given below:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc CR504AC Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info