Bedienungsanleitung Vonroc CR506AC (Seite 5 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch)

819186

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

WWW.VONROC.COM

b) Use personal protective equipment. Always

wear eye protection. Protective equipment

such as dust mask, non-skid safety shoes, hard

hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking up

or carrying the tool. Carrying power tools with

your ﬁnger on the switch or energising power

tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust related hazards.

h) Do not let familiarity gained from frequent use

of tools allow you to become complacent and ig-

nore tool safety principles. A careless action can

cause severe injury within a fraction of a second.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

b) Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot

be controlled with the switch is dangerous and

must be repaired.

Disconnect the plug from the power source and/

or the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools. Such preventive safety

measures reduce the risk of starting the power

tool accidentally.

d) Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in

the hands of untrained users.

e) Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and the

work to be performed. Use of the power tool for

operations different from those intended could

result in a hazardous situation.

h) Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles

and grasping surfaces do not allow for safe

handling and control of the tool in unexpected

situations.

5) Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replacement

parts. This will ensure that the safety of the

power tool is maintained.

SPECIAL SAFETY INSTRUCTIONS

• Warning! The compressor may only be used in

suitable rooms (with good ventilation and an

ambient temperature from 5°C to +40°C).

• Check that the tank is fully decompressed befo-

re connections with the tank are unscrewed.

• It is prohibited to make holes in, or welds to, or

purposely to distort the compressed air tank.

• Do not perform any actions on the compressor

without ﬁrst having taken the plug out of the

plug socket.

• Do not aim water jets or jets of ﬂammable

liquids at the compressor.

• Do not place ﬂammable objects near the com-

pressor.

• Switch the switch (2) to the “0” position (OFF)

during dwell time.

• Never aim the air jet at persons or animals.

• Do not transport the compressor with the tank

pressurised.

• N.B.: some parts of the compressor such as the

head and the feed-through pipes may reach

high temperatures. Do not touch these parts to

avoid burns.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc CR506AC Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info