819186
7
Zoom out
Zoom in
Vorherige Seite
1/112
Nächste Seite
EN
7
WWW.VONROC.COM
TECHNICAL SPECIFICATIONS
Model No. CR506AC /
CR506AC_GREY /
CR506AC_WHITE
Compressor type Piston - oil free -
lownoise
Compressor drive Direct drive
Voltage 220-240V~
Frequency 50 Hz
Input power 750W
Horsepower 1 HP
Operating mode S3 50% *
Idling speed 1450/min
IP class IP30
Protection class Class I
Air intake 128 l/min
Output (compressed air) at 7 bar 42 l/min
Output (compressed air) at 4 bar 65 l/min
Max. outlet pressure 8 bar
Cut-in pressure approx. 6 bar
Cut-out pressure approx. 8 bar
Tank capacity 24L
Cable length 2m
Weight 23 kg
Sound pressure level L
pA
= 79.7 dB(A)
K
pA
= 3 dB(A)
Sound power level L
WA
= 92.7 dB(A)
K
WA
= 3 dB(A)
* S3 = intermittent operation without the impact of
the start-up. This means that during a period of 10
minutes, the maximum operating time is 50% (e.g.
5 minutes of work and 5 minutes of rest) , under
optimal environmental conditions (max. temp
25°C). Respecting these guidelines and the prescri-
bed maintenance intervals will allow the product to
work properly over time.
DESCRIPTION
The numbers in the text refer to the diagrams on
page 2-3.
1. Cover
2. Switch
3. Pressure switch
4. Pressure regulator
5. Quick coupler (outlet)
6. Pressure gauge (operating pressure)
7. Pressure gauge (tank pressure)
8. Safety valve
9. Handle
10. Pressure pipe
11. Drain cock
12. Air inlet
13. Air filter
14. Overload switch
15. Tank
16. Rubber feet
17. Bolts
18. Washers
19. Nuts (for feet)
20. Wheels
21. Axle bolts
22. Lock washers
23. Nuts (for wheels)
24. Allen screws
3. ASSEMBLY
Before assembly, always switch off the
machine and remove the mains plug from
the mains.
Mounting the wheels (Fig. A, B)
1. Insert the wheel axle bolt (21) into the intended
hole of the wheel (20).
2. Mount the wheel (20) on one side of the tank
(15). Using the supplied lock washer (22) and
nut (23) as shown on figure B.
3. Tighten the nut (23) by using a wrench.
4. Repeat these steps for the other wheel (20) on
the other side of the tank (15).
Assembling the rubber feet (Fig. A, C)
1. Insert the bolt (17) into the intended hole of the
washer (18).
2. Insert the bolt (17) into the intended hole of the
rubber foot (16).
3. Mount the rubber foot (16) on one of the two
mounting points on the bottom of the tank (15)
as shown on figure C.
4. Tighten the nut (19) by using a wrench.
5. Repeat these steps for the other foot (16) on
the other mounting point.
7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Vonroc CR506AC wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info