Bedienungsanleitung Vonroc CR506AC (Seite 8 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch)

819186

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

WWW.VONROC.COM

Assembling the handle (Fig. A, D)

1. Insert the handle (9) into the intended holes of

the tank (15), as shown on ﬁgure D.

2. Insert the 4 allen screws (24) in the holes and

tighten by turning clockwise by using an allen

key, as shown on ﬁgure D.

Mounting the air ﬁlter (Fig. A, E)

1. Remove the transport lid and replace them with

the supplied air ﬁlter (13) before using the com-

pressor.

2. Mount the air ﬁlter (13) by screwing the air ﬁlter

(13) clockwise into the air inlet (12) as shown

on ﬁgure E.

Installing the compressor

• The compressor should be installed in ventila-

ted and dry environment.

• Make sure the compressor is placed on the

horizontal and stable ground.

• Place the compressor on a ﬂat surface or at a

maximum slope of 10°, in a well ventilated area,

protected against atmospheric factors and not

in explosive surroundings.

• If the surface area is sloping and smooth, make

sure that the compressor will not move when in

operation.

• For proper ventilation and effective cooling, it is

important that the compressor is positioned at

least 50 cm away from any wall or obstacle.

• Make sure that the compressor is transported

in the right way, do not turn it upside down and

don’t lift it with hooks or ropes.

4. OPERATION

You must fully assemble the compressor

before using it for the ﬁrst time.

Long supply cables, extensions, cable reels

etc cause a drop in voltage and can impede

motor start-up. Do not use cables longer

than 10m. Vonroc advises to use a longer

air hose instead.

It can be more difﬁcult to start-up the motor

during conditions of temperatures below

5°C.

The head/cylinder/transmission pipe

assembly may reach high temperatures, so

take care when working close to these

parts and do not touch them to avoid burns.

Starting up (Fig. A)

1. Check whether the mains voltage corresponds

to that indicated on the electrical speciﬁcation

plate.

2. Push the ON/OFF switch (2) into the position ‘O’

to switch the compressor off.

3. Put the plug in the plug socket.

4. Pull the ON/OFF switch (2) into the position ‘I’

to switch the compressor on.

5. The operation of the compressor is fully

automatic. The pressure switch (3) will stop

the compressor when the maximum value has

been reached and start it up when the pressure

drops below the minimum value. The pressure

switch (3) is set at the factory. Normally the

difference in pressure is approx. 2 Bar/29 psi

between the maximum and the minimum value.

The compressor will stop when it reaches 8

Bar (116 psi) (this is the maximum operating

pressure) and will start up automatically when

the pressure within the tank has dropped to 6

Bar (87 psi).

Connecting the air hose and tool (Fig. A)

1. Turn the pressure regulator (4) turning knob

anti-clockwise till pressure is fully released.

2. Insert the connector of the air hose (not inclu-

ded) into the quick coupler (5) on the compres-

sor. When pushing, the connector clicks into

place to secure the air hose.

3. Connect the air tool (not included) you want to

use to the quick coupler of the air hose.

4. Turn the pressure regulator (4) turning knob

clockwise, till the pressure gauge (6) shows the

pressure level you need.

5. Your air tool is now ready to use.

Disconnecting the air hose and tool (Fig. A)

When releasing the quick coupler, be sure

to hold the hose to protect yourself from

injury from the rebounding hose.

1. Turn the pressure regulator (4) turning knob

anti-clockwise till pressure is fully released.

2. Reduce the pressure by activating the air tool

(not included).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc CR506AC Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info