Bedienungsanleitung Vonroc CR506AC (Seite 9 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch)

819186

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

WWW.VONROC.COM

3. Pull back the sleeve on the air hose quick

coupler and remove your air tool.

4. Pull back the sleeve on the quick coupler (5)

and remove the hose.

Reading the pressure (Fig. A)

The compressor has two pressure gauges (6,7).

The tank pressure can be read on the pressure

gauge (7) and the operating pressure (regulated

pressure) can be read on the pressure gauge (6).

The black scale indicates the pressure in bar and

the red scale indicates the pressure in PSI.

Adjusting the operating pressure (Fig. A)

It is not always necessary to use the

maximum operating pressure. The air tools

often require less pressure. Always check

the correct operating pressure of the tool

you intend to use.

With regard to compressors supplied with a

pressure regulator (4) it is necessary to set the

operating pressure properly. It is possible to set the

operating pressure by using the turning knob on

the pressure regulator (4):

• By turning clockwise, the operating pressure

will be increased.

• By turning anti-clockwise, the operating pressu-

re will be reduced.

Note: when not connecting an air tool while ad-

justing the pressure, it might occur the pressure

gauge (6) is not reacting accurately on the pressu-

re drop.

Overload switch (Fig. A)

The motor is ﬁtted with an overload switch (14). If

the compressor overloads, the overload switch (14)

switches the equipment off automatically to protect

the compressor from overheating. If the overload

switch (14) triggers, switch off the compressor

using the ON/OFF switch (2) and wait until the

compressor cools down. Then press the overload

switch (14) and restart the compressor.

Finish operation (Fig. A, F)

Do not touch the compressor unless its

power has been cut off for at least 10

minutes.

When there is the risk of frost or if you do

not use your compressor for a long time,

please properly store your compressor.

1. Check that the ON/OFF switch (2) is in the ‘O’

position.

2. Remove the mains plug from the mains.

Reduce the pressure in the tank till approximately

2 bar by connecting and activating an air tool.

4. Then slowly turn the drain cock (11) on the lo-

wer side of the tank open. The water in the tank

(15) will now leak out of the tank (15).

5. Take care when compressed air is in the tank

(15) because the water can come out with some

force. Recommended pressure max. 1-2 Bar.

6. Remove the air tool and hose.

7. Clean and store the device (see ‘Maintenance’).

5. MAINTENANCE

Before cleaning and maintenance, always

switch off the machine and remove the

mains plug from the mains.

Do not touch the compressor unless its

power has been cut off for at least 10

minutes. Risk of burns!

Always depressurize the tank before

carrying out any cleaning and maintenance

work.

Clean the machine casings regularly with a soft

cloth, preferably after each use. Make sure that the

ventilation openings are free of dust and dirt. Re-

move very persistent dirt using a soft cloth moiste-

ned with soapsuds. Do not use any solvents such

as gasoline, alcohol, ammonia, etc. Chemicals such

as these will damage the synthetic components.

Drain the tank (Fig. F)

Check the pressure tank for signs of rust

and damage each time before using. Do not

use the compressor with a damaged or

rusty pressure vessel.

Compressing air will cause water in the tank. Regu-

larly drain the water from the tank to prevent tank

corrosion. It depends on the humidity, but advice is

after each use.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc CR506AC Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info