Bedienungsanleitung Vonroc HA501AC (Seite 7 von 28) (Deutsch, Englisch, Holländisch, Französisch)

764012

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

WWW.VONROC.COM

• Smelting synthetics, among which matters and

foils with PVC layer;

• Applying heat shrinking tubes;

• Shrinkwrappers;

• Thawing tubes and engines;

• Repairing ﬁnishing layers: enamel of bath and

household appliances; applying epoxypowder

coverlayers;

• Repairing of ski’s, surf-boards and other sports

goods;

•

Unscrewing too fast ﬁxed screws and connections.

Operation (Fig. A)

You can work manually with this hot air gun or you

can put it in a vertical position.

• Check if the mains switch is on position “0”

before you connect the apparatus;

• Keep the main lead always away from the hot

air stream and the mouth piece;

• Put the mains switch in position ‘I or II’ to let

your hot air gun operate:

“I” = 400 degrees, air ﬂow 250 l/min.

“0” = Off

“II” = 600 degrees, air ﬂow 500 l/min.

Switching off:

Slide the switch to 0.

Tip: If you want to get the best result, test all appli-

ances on a little part of the workpiece.

Flat rear side (Fig. C)

Inbetween usage, the machine can easily be placed

on its ﬂat rear side (7). This prevents any hot area

from the machine getting into contact with other

surfaces

The ﬂat rear side (7) also allows the machine to be

used in upright stationary mode.

After usage, always place the machine on its ﬂat

rear side (7). This allows the machine to cool down

safely.

Use of accessoires (Fig. B)

Fishtail nozzle (4)

Distributes air equally over ﬂat wide area.

Reduction nozzle (5)

Distributes air equally over small areas

Glass protection nozzle (6)

Deﬂects air away from glass for example when

stripping paint in window frames or softening putty.

4. MAINTENANCE

Always disconnect the apparatus before

carrying out inspection or cleaning. Never

use water or other liquids to clean the

electrical parts of the hot air gun.

• Never use easy inﬂammable liquids for cleaning

the hot air gun, especially for the mouthpiece.

• Regular maintenance of your hot air gun

prevents unnecessary problems. Keep the ven-

tilation slots of the hot air gun clean to prevent

overheating.

Troubleshooting

In case the hot air gun does not work well, we give

you subjoined some possible causes and their

solutions.

• The engine gets overheated.

•

The ventilation slots of the hot air gun are dirty.

Clean the ventilation slots.

• The hot air gun does not start when it is

switched on.

• Interruption in the electrical circuit.

Check the mains lead and the mains plug.

• The switch is defective.

Pull the mains lead out of the wall socket, be-

cause there is a chance of ﬁre risk! Have the hot

air gun repaired at your local dealer.

• The engine does not work, but it does heat.

• Interruption in the electrical circuit.

Pull the mains lead out of the wall socket,

because there is a chance of ﬁre risk! Have the

hot air gun repaired at your local dealer.

ENVIRONMENT

Faulty and/or discarded electrical or

electronic apparatus have to be collected at

the appropriate recycling locations.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc HA501AC Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Vonroc HA501AC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info