Bedienungsanleitung Vonroc MS503AC (Seite 9 von 88) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

764094

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

WWW.VONROC.COM

objects that can make a connection from one

terminal to another. Shorting the battery termi-

nals together may cause burns or a ﬁre.

Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact acci-

dentally occurs, ﬂush with water. If liquid contacts

eyes, additionally seek medical help. Liquid ejec-

ted from the battery may cause irritation or burns.

e) Do not use a battery pack or tool that is dama-

ged or modiﬁed. Damaged or modiﬁed batteries

may exhibit unpredictable behaviour resulting

in ﬁre, explosion or risk of injury.

f) Do not expose a battery pack or tool to ﬁre

or excessive temperature. Exposure to ﬁre or

temperature above 130 °C may cause explo-

sion. NOTE The temperature „130 °C“ can be

replaced by the temperature „265 °F“.

g) Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range speciﬁed in the instructi-

ons. Charging improperly or at temperatures

outside the speciﬁed range may damage the

battery and increase the risk of ﬁre.

6) Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replacement

parts. This will ensure that the safety of the

power tool is maintained.

Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized service providers.

SPECIFIC SAFETY INSTRUCTIONS

• Mitre saws are intended to cut wood or wood-li-

ke products, they cannot be used with abrasive

cut-off wheels for cutting ferrous material such

as bars, rods, studs, etc. Abrasive dust causes

moving parts such as the lower guard to jam.

Sparks from abrasive cutting will burn the lower

guard, the kerf insert and other plastic parts.

• Use clamps to support the workpiece whenever

possible. If supporting the workpiece by hand,

you must always keep your hand at least 100 mm

from either side of the saw blade. Do not use this

saw to cut pieces that are too small to be secure-

ly clamped or held by hand. If your hand is placed

too close to the saw blade, there is an increased

risk of injury from blade contact.

• The workpiece must be stationary and clamped

or held against both the fence and the table.

Do not feed the workpiece into the blade or cut

“freehand” in any way. Unrestrained or moving

workpieces could be thrown at high speeds,

causing injury.

• Push the saw through the workpiece. Do not

pull the saw through the workpiece. To make a

cut, raise the saw head and pull it out over the

workpiece without cutting, start the motor, press

the saw head down and push the saw through

the workpiece. Cutting on the pull stroke is likely

to cause the saw blade to climb on top of the

workpiece and violently throw the blade assem-

bly towards the operator.

• Never cross your hand over the intended line of

cutting either in front or behind the saw blade.

Supporting the workpiece “cross handed” i.e.

holding the workpiece to the right of the saw

blade with your left hand or vice versa is very

dangerous.

• Do not reach behind the fence with either hand

closer than 100 mm from either side of the saw

blade, to remove wood scraps, or for any other

reason while the blade is spinning. The proximity

of the spinning saw blade to your hand may not

be obvious and you may be seriously injured.

• Inspect your workpiece before cutting. If the

workpiece is bowed or warped, clamp it with the

outside bowed face toward the fence. Always

make certain that there is no gap between the

workpiece, fence and table along the line of the

cut. Bent or warped workpieces can twist or

shift and may cause binding on the spinning saw

blade while cutting. There should be no nails or

foreign objects in the workpiece.

• Do not use the saw until the table is clear of all

tools, wood scraps, etc., except for the workpie-

ce. Small debris or loose pieces of wood or other

objects that contact the revolving blade can be

thrown with high speed.

• Cut only one workpiece at a time. Stacked multi-

ple workpieces cannot be adequately clamped or

braced and may bind on the blade or shift during

cutting.

• Ensure the mitre saw is mounted or placed on a

level, ﬁrm work surface before use. A level and

ﬁrm work surface reduces the risk of the mitre

saw becoming unstable.

• Plan your work. Every time you change the bevel

or mitre angle setting, make sure the adjustable

fence is set correctly to support the workpie-

ce and will not interfere with the blade or the

guarding system. Without turning the tool “ON”

and with no workpiece on the table, move the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc MS503AC Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info