Bedienungsanleitung Vonroc MS503AC (Seite 10 von 88) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

764094

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

WWW.VONROC.COM

saw blade through a complete simulated cut to

assure there will be no interference or danger of

cutting the fence.

• Provide adequate support such as table exten-

sions, saw horses, etc. for a workpiece that is

wider or longer than the table top. Workpieces

longer or wider than the mitre saw table can tip

if not securely supported. If the cut-off piece or

workpiece tips, it can lift the lower guard or be

thrown by the spinning blade.

• Do not use another person as a substitute for

a table extension or as additional support. Un-

stable support for the workpiece can cause the

blade to bind or the workpiece to shift during the

cutting operation pulling you and the helper into

the spinning blade.

• The cut-off piece must not be jammed or pressed

by any means against the spinning saw blade. If

conﬁned, i.e. using length stops, the cut-off piece

could get wedged against the blade and thrown

violently.

• Always use a clamp or a ﬁxture designed to

properly support round material such as rods or

tubing. Rods have a tendency to roll while being

cut, causing the blade to “bite” and pull the work

with your hand into the blade.

• Let the blade reach full speed before contacting

the workpiece. This will reduce the risk of the

workpiece being thrown.

• If the workpiece or blade becomes jammed,

turn the mitre saw off. Wait for all moving parts

to stop and disconnect the plug from the power

source and/or remove the battery pack. Then

work to free the jammed material. Continued

sawing with a jammed workpiece could cause

loss of control or damage to the mitre saw.

• After ﬁnishing the cut, release the switch, hold

the saw head down and wait for the blade to stop

before removing the cut-off piece. Reaching with

your hand near the coasting blade is dangerous.

• Hold the handle ﬁrmly when making an incom-

plete cut or when releasing the switch before

the saw head is completely in the down position.

The braking action of the saw may cause the saw

head to be suddenly pulled downward, causing a

risk of injury.

• Keep your work area clean. Material mixtures

are particularly hazardous. Light metal dust may

catch ﬁre or explode.

• Do not use dull, cracked, bent or damaged saw

blades. Unsharpened or improperly set saw

blades produce narrow kerf causing excessive

friction, blade binding and kickback.

• Do not use saw blades made from high speed

steel (HSS). Such saw blades can easily break.

•

Always use saw blades with correct size and

shape (diamond versus round) of arbour holes.

Saw blades that do not match the mounting

hardware of the saw will run off-centre, causing

loss of control.

• Do not replace the integrated laser with a laser

of another type. A laser that is not compatible

with this power tool could pose a risk to persons.

• Never remove cuttings, wood chips, etc. from

the cutting area while the power tool is running.

Always guide the tool arm back to the neutral

position ﬁrst and then switch the power tool off.

• Do not touch the saw blade after working before

it has cooled. The saw blade becomes very hot

while working.

• Never make warning signs on the machine unre-

cognisable.

• If laser radiation hits your eye, you must close

your eyes and immediately turn your head away

from the beam.

• Do not use any optical instruments such as

binoculars to view the radiation source. Doing

so can damage your eye.

• Do not direct the laser beam at persons who are

looking through binoculars or similar instru-

ments. Doing so can damage their eye.

• Do not make any modiﬁcations to the laser

equipment. The setting options described in

these operating instructions can be used safely.

• Do not stand in line with the saw blade in front

of the power tool. Always stand to the side of

the saw blade. This protects your body against

possible kickback.

• Keep hands, ﬁngers and arms away from the

rotating saw blade.

• Do not reach one hand across the other when in

front of the tool arm.

• Avoid overheating of the saw teeth. When the

saw blade overheats, stop the machine. Allow

the saw blade to cool down before using the

machine again.

• Replace damaged or worn saw blades immedi-

ately.

• Only use saw blades that match the speciﬁca-

tions given in this operating manual and that

have been tested and marked in accordance

with EN 847-1.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc MS503AC Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info