Bedienungsanleitung Vonroc MS503AC (Seite 11 von 88) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

764094

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

WWW.VONROC.COM

• When sawing curved or round workpieces,

these must be especially secured against slip-

ping. At the cutting line, there should be no gap

between the workpiece, fence and saw table. If

necessary, you will need to manufacture special

ﬁxtures.

Electrical safety

Always check that the voltage of the power

supply corresponds to the voltage on the

rating plate.

• Do not use the machine if the mains cable or

the mains plug is damaged.

•

Only use extension cables that are suitable for

the power rating of the machine with a minimum

thickness of 1.5 mm2. If you use an extension

cable reel, always fully unroll the cable.

2. MACHINE INFORMATION

Intended use

This tool is intended as a stationary machine for

making straight lengthways and crossways cuts in

wood with and against the grain. It is possible to

cut mitre angles of -45° to +45° and bevel angles of

-0° to +45°. The power tool with the ﬁtted sawbla-

de is designed with sufﬁcient capacity for sawing

hardwood and softwood as well as chipboard and

ﬁbreboard. The sawblade is not designed for cut-

ting ﬁrewood. Do not use the saw to cut materials

other than those speciﬁed described in manual.

TECHNICAL SPECIFICATIONS

Model No. MS503AC

Voltage 220-240V~

Frequency 50 Hz

Power input 1400W S1 - 1700W S6

25%*

No load speed 4900/min

Mitre angles -45° <> +45°

Bevel angles -45° <> 0° to the left,

single bevel

Sawblade speciﬁcations:

Diameter

Base blade thickness

Width of cut

Bore diameter

Number of teeth

Ø 216 mm

1.6 mm

2.8 mm

Ø 30 mm

40T

Saw capacity (height x width):

Mitre 0° - Bevel 0°

Mitre 0° - Bevel 45°

Mitre 45° - Bevel 0°

Mitre 45° - Bevel 45

60 x 115 mm

25 x 115 mm

60 x 80 mm

25 x 80 mm

Minimum workpiece dimen-

sions 3 x 10 mm

Laser speciﬁcations:

Class

Wavelength

Output

650 nm

< 1 mW

Weight 6.9 kg

Lpa (sound pressure level) 92.7 +3 dB(A)

Lwa (sound power level) 103.7 +3 dB(A)

Vibration value <2.5 m/s2

* S6, continuous operation periodic duty. Identi-

cal duty cycles with a period at load followed by

a period at no load. Running time 10 minutes;

duty cycle is 25% of the running time.

Vibration level

The vibration emission level stated in this instruc-

tion manual has been measured in accordance

with a standardised test given in EN 60745; it may

be used to compare one tool with another and as

a preliminary assessment of exposure to vibration

when using the tool for the applications mentioned

- using the tool for different applications, or with

different or poorly maintained accessories, may

signiﬁcantly increase the exposure level.

- the times when the tool is switched off or when

it is running but not actually doing the job, may

signiﬁcantly reduce the exposure level.

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work patterns

DESCRIPTION

The numbers in the text refer to the diagrams on

page 2-6.

1. Lock-off button

2. Handle

3. On/off switch

4. Protective guard

5. Retracting protective guard

6. Saw blade

7. Adjustable fence

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc MS503AC Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info