Bedienungsanleitung Vonroc MS503AC (Seite 12 von 88) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

764094

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

WWW.VONROC.COM

8. Fence

9. Table extension

10. Table

11. Mounting holes

12. Kerf plate

13. Knob for mitre adjustment

14. Locking bolt for mitre adjustment

15. Scale for mitre angle

16. Indicator for mitre angle

17. Laser

18. Indicator for bevel angle

19. Scale for bevel angle

20. Workpiece clamp

21. Knob for bevel adjustment

22. Depth adjustment bolt

23. Dust bag

24. Carrying handle

25. Dust outlet

26. Rear tilt protector

27. Stop bolt for 45° bevel angle

28. Stop bolt for 0° bevel angle

29. Locking bolt for workpiece clamp

30. Hex key

31. Locking bolt for adjustable fence

32. Adjustment bolt for fence

33. Position lock knob

34. Screws

35. Retaining bolt

36. Clamping ﬂange

37. Clamping bolt

38. Spindle lock

39. Knob for workpiece clamp

40. Knurled nut for depth adjustment

41. EN laser switch

42. Screws for laser adjustment

43. Lock nut for 45° bevel angle

44. Lock nut for 0° bevel angle

45. Fence bolts

3. ASSEMBLY

Before carrying out any work on the

machine, disconnect the mains plug from

the power supply.

Mounting the knob for mitre adjustment (Fig. A)

Mount the knob for mitre adjustment (13) by simply

screwing it clockwise in the thread.

Mounting the carrying handle (Fig. E)

1. Mount the handle on top of the machine, as

shown on Figure E.

2. Tighten the screws using a philips headed

screwdriver.

Transport position (Fig. B, C)

The position lock knob (33) makes it easier to move

the power tool when transporting it to various

working locations.

Unlocking the transport position (work position)

1. Press the handle (2) downwards slightly;

2. Pull the position lock knob (33) fully outwards

and lock it in place by turning it;

3. Slowly move the handle (2) upwards.

Locking the transport position (transport position)

Before locking in transport position, make sure

that the depth adjustment bolt (22) is adjusted to

unlimited depth. This way, the handle (2) can be

moved fully downwards without touching the depth

stop. Also, remove all accessories that cannot be

securely ﬁtted to the machine.

1. Press the handle (2) fully downwards;

2. Lock the position lock knob (33) by ﬁrst pulling

and then turning it;

3. Wind up the mains cable and tie it together with

the supplied cable strap.

After locking the transport position, use the carrying

handle (24) to safely carry and transport the machine.

Only use the carrying handle to transport the

machine and never the protective guards.

Install of a stationary machine (Fig. A, B, D)

To ensure safe handling, the power tool must be moun-

ted on a ﬂat, stable work surface (e.g. work bench)

before use. You can install the machine in three ways:

1. On a workbench

In this case the machine must be secured to the

workbench using suitable screw fasteners. Use the

four holes (11) to do this. As shown on ﬁg. D.

2. On a subframe

Read all the warnings and instructions

included with the saw stand. Failure to

observe the warnings and follow instructi-

ons may result in electric shock, ﬁre and/or

serious injury.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc MS503AC Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info