Bedienungsanleitung Watts Climatic Control Heating and Cooling (Seite 14 von 28) (Englisch)

805499

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

6. Types of operating modes / Program menu

6.1 Heating and cooling switch

There are several ways to switch the system between heating and cooling.

 Use parameter #0 Type (See Chap 7.1)

 Use the user interface of the Climatic Control HC if parameter #0 Type=Rev (See Chap 7.1)

 Use the user interface of the paired MILUX-RF HYGROSTAT if parameter #0 Type=Rev

 Use Input 1 parameter #11 In1=HC or Input 2 parameter #12 In2 =HC (See Chap 5.4.7 and Chap 7.1)

6.2 Types of operating modes

Selection of the operating mode is done using the arrow keys (◄) and (►). The cursor must be positioned on the

symbol of the relevant operating mode.

COMFORT mode of operation

Unlimited operation in COMFORT mode .

The system runs in constant comfort mode. The ClimaticControl-HC adjusts the flow temperature depend-

ing on the outdoor temperature and the selected curve. No temperature setback.

The display Pos. 5 shows the current flow temperature and the outside temperature at 13 (damped val-

ue). By pressing the button (OK) the preset value of flow temperature appears for about 3 seconds at 5.

At the same time the manually selectable deviation is displayed at 13 (factory setup: 00.0 = no deviation).

Using the buttons (+) or (-) you can adjust the preset value of the flow temperature. If changed, the sym-

bol

appears on the display.

In heating mode of operation if no room thermostat is installed ( MuB:  5.3), the circulation pump is

running continuously. The pump switches off if the mixing 3 way valve is closed for the setting time

(PUMP:  System parameters: pump delay time). That is the case when the room heating is sufficient

and the room thermostat closes all heating circuits by means of actuators. The same happens when the

value of flow temperature calculated by the ClimaticControl-HC becomes lower than the actual tempera-

ture value because of rising outdoor temperatures. If the actual value of the flow temperature falls below

the preset value, the pump will restart.

In this case to ensure a correct measure of the water temperature the pump will be start each 30min

for a short time to measure the real temperature of water inside the hydraulic circuit.

To ensure energy saving operating mode of the pump it could be switched by a “pump logic” of a elec-

tric connecting box. The connecting box is normally used together with room thermostats and electro-

thermic actuators. The “pump logic” is a potential free switching relay, the contact of which is closed

whenever higher temperature is demanded in any of the rooms. If all rooms are warm enough, the contact

opens and the pump turns off. ( MuB:  5.5)

If the heat generator / boiler (WE) is in temperature setback and the temperature supplied by the WE

is below the preset temperature calculated by the ClimaticControl-HC, heating mode is not available.

However if the circulation pump is actually running and the 2/3-way valve may also be opened by the 3-

point actuator because of room heating demand, the preset value of flow temperature may be exceeded

for a short period of time when the WE switches to heating mode. In this case, if a temperature limiter is

available, the pump might switch off and then pump operation will be possible only after the temperature

drops below the preset maximum temperature of the TB.

Trouble-shooting: The TB should be installed at a greater distance from the control unit. If necessary you

can set the TB to a higher temperature until the pump starts. After a few minutes of pump operation the

maximum allowable temperature set on the TB should be restored. Alternatively you can remove the TB

from the pipe for a while and leave the pump running for a few minutes. Then refit the TB again to the

pipe.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Watts Climatic Control Heating and Cooling Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info