Bedienungsanleitung Webasto Live (Seite 27 von 79) (Deutsch, Englisch, Holländisch, Italienisch, Spanisch)

802116

Zoom out

Zoom in

Vorherige Seite

1/79

Nächste Seite

5110326C_OI-II_Webasto Live 15

– The Webasto Live charging station also meters

the plug-in cycles of the charge coupling for ser-

vice purposes and after 10,000 plug-in cycles, dis-

plays a note on the web interface that an electri-

cian needs to inspect the plug contacts on the

charge coupling for any signs of wear. If any signs

of wear are discovered, the electrician must re-

place the affected charging cables with genuine

Webasto spare parts.

– Do not attach extension cables or adapters to the

charging cable.

– Remove the charging cable by pulling on the

charging coupling only.

– Never clean the charging station with a high-pres-

sure cleaner or similar device.

– Switch off the power supply before cleaning the

charging sockets.

– The charging cable must not be subjected to any

strain during use.

– Ensure only persons who have read these operat-

ing instructions have access to the charging sta-

tion.

2.3 Safety information for installation

– Installation and connection of the charging sta-

tion must only be carried out by an electrician.

– Only use the supplied installation material.

– The Webasto Live safety concept is based on a

power supply system that is earthed at all times.

The electrician must ensure this requirement dur-

ing installation.

– Do not install the charging station in an explosion

sensitive area (EX zone).

– Install the charging station in such a way that the

charging cable does not block any passageways.

– Do not install the charging station in areas subject

to ammonia or air containing ammonia.

– Do not install the charging station in a location

where falling objects (e.g. extension reel or tyres)

can damage the charging station.

– The charging station is suitable for use indoors as

well as outdoors.

– Do not install the charging station in the vicinity of

water jets, e.g. car wash installations, high pres-

sure cleaners or garden hoses.

– Protect the charging station against damage

caused by sub-zero temperatures, hail or similar.

– The charging station is suitable for use in areas

without access restrictions.

– Protect the charging station from direct sunlight.

The charging current may be reduced at high tem-

peratures or charging may be disabled completely.

– The installation location of the charging station

should be selected such that vehicles cannot inad-

vertently collide with it. Protective measures must

be implemented if the possibility of damage can-

not be ruled out.

– Do not place the charging station into operation if

it is damaged during installation. A replacement

will be required.

2.4 Safety information for electrical

connection

– Comply with the locally applicable requirements

pertaining to electrical installations, fire protec-

tion, safety regulations and escape routes at the

intended installation location.

– Each charging station must be protected with its

own line circuit breaker and residual current circuit

breaker. See chapter6.2, "Criteria for the elec-

trical connection" on page 17.

– Make sure that the electrical connections are de-

energised before connecting the charging station

to the power supply.

– Make sure that the correct supply cable is used for

the power connection.

– Do not leave the charging station unattended

with the cover open.

– Register with the power supply company as re-

quired.

2.5 Safety information for initial startup

– Initial startup of the charging station must be car-

ried out only by an electrician.

– Prior to initial startup, the electrician must check

that the charging station has been connected cor-

rectly.

– Do not connect a vehicle during initial startup of

the charging station.

– Before startingup the charging station, check the

charging cable, charging coupling and the char-

ging station for visible damage. The charging sta-

tion must not be started up if it is damaged or if

the charging cable/charging coupling is damaged.

3Unit description

Fig.1

These operating and installation instructions describe the

Webasto Live charging station. The exact unit description

is indicated on the type label of the charging station.

3.1 Description of data interface connections

Fig.2

Legend

USB-A

Modbus (RS 485) external

Micro SIM-slot

RJ 45 (LAN)

USB-B

With the cover open, the data interfaces can be found on

the left-hand side in the connection area. This area is

separated from the power supply area.

3.1.1 USB type A

This connection is used in host mode for a USB stick for

software or configuration updates. This connection sup-

ports the 5 V power supply up to maximum 100 mA.

3.1.2 Modbus

The data connection to a primary electricity meter can be

established for advanced power management. (see on-

line configuration instructions: https://webasto-

charging.com/documentation)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Webasto Live Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Webasto Live

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info