Bedienungsanleitung Webasto Pure II (Seite 14 von 379) (Alle Sprachen)

802209

Zoom out

Zoom in

Vorherige Seite

1/379

Nächste Seite

2 5110757E OI II Webasto Pure

– The Webasto Live charging station also meters the

plug-in cycles of the charge coupling for service

purposes and after 10,000 plug-in cycles, displays

a note on the web interface that an electrician

needs to inspect the plug contacts on the charge

coupling for any signs of wear. If any signs of

wear are discovered, the electrician must replace

the affected charging cables with genuine

Webasto spare parts.

– Do not attach extension cables or adapters to the

charging cable.

– Remove the charging cable by pulling on the char-

ging coupling only.

– Never clean the charging station with a high-pres-

sure cleaner or similar device.

– Switch off the power supply before cleaning the

charging sockets.

– The charging cable must not be subjected to any

strain during use.

– Ensure only persons who have read these operat-

ing instructions have access to the charging sta-

tion.

WARNING

– When not in use, store the charging cable in the

designated holder and lock the charging coupling

in the remote dock. Loosely wind the charging

cable around the remote dock making sure the

cable does not touch the floor.

– You must make sure that the charging cable and

coupling cannot be driven over, trapped and are

protected from all other hazards.

2.3 Safety information for installation

– You must comply with the locally applicable re-

quirements regarding electrical installations, fire

protection, safety regulations, and escape routes

at the intended installation location.

– Only use the supplied installation material.

– When open, ESD (electrostatic discharge) precau-

tions must be taken properly to avoid electrostatic

discharge.

– When handling electrostatically sensitive boards,

wear grounded antistatic wrist straps and properly

observe ESD safety precautions. Wrist straps must

only be used when mounting and connecting the

loading unit. Wrist straps must never be worn on

a live Webasto Pure.

– Electricians must be properly grounded during in-

stallation of the Webasto Pure.

– Do not install the Webasto Pure in an explosion

sensitive area (Ex Zone).

– Install the Webasto Pure in such a way that the

charging cable does not block any passageways.

– Do not install the Webasto Pure in areas subject to

ammonia or air containing ammonia.

– Do not install the Webasto Pure in a location

where falling objects may damage the it.

– The Webasto Pure is suitable for use indoors as

well as outdoors.

– Do not install the Webasto Pure in the vicinity of

water jets, such as car-wash installations, high-

pressure cleaners or garden hoses.

– Protect the Webasto Pure against damage caused

by sub-zero temperatures, hail or similar. We

would like to refer you to our IP protection class at

this juncture (IP54).

– The Webasto Pure is suitable for use in areas

without access restrictions.

– Protect the Webasto Pure from direct sunlight.

The charging current may be reduced at high tem-

peratures, or charging may be disabled com-

pletely. For the 11 kW variant the operating tem-

perature range is -30 °C to +55 °C and for the 22

kW variant from -30 °C to +45 °C.

– The installation location of the Webasto Pure

should ensure that vehicles cannot inadvertently

collide with it. Protective measures must be imple-

mented if the possibility of damage cannot be

ruled out.

– Do not put the Webasto Pure into operation if it

has been damaged during installation; a replace-

ment will be required.

2.4 Safety information for electrical

connection

WARNING

– Comply with the nationally applicable require-

ments pertaining to electrical installations, fire

protection, safety regulations and escape routes

at the intended installation location. Observe the

applicable national installation regulations.

– Each charging station must be protected with its

own line circuit breaker and residual current circuit

breaker. See Requirements at the installation loca-

tion.

– Make sure that the electrical connections are de-

energised before connecting the charging station

to the power supply.

– Do not connect a vehicle during initial start-up of

the charging station.

– Make sure that the correct supply cable is used for

the power connection.

– Do not leave the charging station unattended with

the cover open.

– Change DIP-switch settings only with the power

off.

– Register with the power supply company as re-

quired.

2.4.1 Safety information for electrical connection

– Comply with the nationally applicable require-

ments pertaining to electrical installations, fire

protection, safety regulations and escape routes

at the intended installation location. Observe the

applicable national installation regulations.

– Each charging station must be protected with its

own line circuit breaker and residual current cir-

cuit breaker. See Requirements at the installation

location.

– Make sure that the electrical connections are de-

energised before connecting the charging station

to the power supply.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Webasto Pure II Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info