Bedienungsanleitung Wmf KULT X - 15140011 (Seite 12 von 55) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

690795

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

22 23

Setting the timer

If you do not want to start the baking process straight away you can use the timer function. You can

set the time when you want your bread to ﬁnish baking in 10-minute increments by using the – and +

buttons, and the baking time is taken into account. The maximum delay cycle is 13 hours.

Note: This function is not available with the following programmes: ultra-fast programme, preserves

and baking.

Note: Do not use any perishable foodstuffs such as eggs or fresh milk when using the timer function.

Keep-warm function

After the baking time has ﬁnished, the 60-minute keep-warm period starts automatically. If you want

to remove the bread immediately after baking, hold down the Start/Stop button

Start

Stop

to stop the baking

process.

Memory function

If the power supply is temporarily interrupted during the baking process, the process will automatically

restart within 10 minutes without needing to press the Start/Stop button

Start

Stop

. If the power cut lasts

longer than 10 minutes, you must restart the bread maker.

Useful tips

▪ Heavy dough: For heavy dough it is recommended that you change the sequence. Add the dry

ingredients to the baking pan ﬁrst followed by the liquid ingredients. If you want to use the timer

function however, make sure that the yeast does not come into contact with the liquid prematurely.

▪ Baking mixtures: The programme for the classic loaf (no. 1) is generally suitable for baking mixtures,

unless speciﬁed otherwise in the recipe. Do not add any more water to the baking mixture than

the amount speciﬁed in the recipe. Depending on the recipe, it may be recommended to reduce the

amount of water by up to 50 ml.

▪ Browning: Since the bread maker does not have a heat source around the lid, it is recommended

that you use the maximum browning level if you want your bread to have a crispy texture.

▪ Eggs: If you are using extra eggs then the amount of liquid must be adjusted accordingly. It is also

recommended that you beat the eggs before adding them to the baking pan.

▪ Backing chamber lighting: To replace the light bulb you can remove the glass cover with a coin.

Please use an oven light bulb with the following characteristics:

⋅ E14

⋅ Total length 49 mm

⋅ Glass diameter 22 mm

⋅ 220-240V

⋅ 15W

⋅ 300°C

Cleaning and care

Remove the mains plug after use. Allow the bread maker to cool down before cleaning it. Remove

the baking pan by holding the handle and twisting it in an anti-clockwise direction. Then remove

the dough hook. If the dough hook is difﬁcult to remove, ﬁll the baking pan with lukewarm water

for around 30 minutes and leave the dough hook to soak in it. Now it should be easier to remove.

Clean the baking pan and the dough hook with a damp cloth, and avoid using sharp or abrasive

cleaning agents that could otherwise damage the non-stick coating. The baking pan must be dried out

completely before it can be used again. Use a damp cloth to clean the bread maker, the lid and the

window. Do not use any abrasive cleaning agents as this could damage the surface. Never submerge

the casing in water. You can put the measure, the measuring spoon and the dough hook remover in

the dishwasher to make cleaning simple.

Dishwasher safe

Can be rinsed

under running

water

Wipe with a damp

cloth

Baking pan

Kneading hook

Measuring cup

Measuring spoon

Hook remover

Casing

Troubleshooting

The display shows “HHH” (accompanied by 5 beeps)

The internal temperature is too high. You must stay on the current programme. Open the lid and leave

the bread maker to cool down for 10 to 20 minutes.

The display shows “LLL” (accompanied by 5 beeps) after pressing the Start/Stop button

Start

Stop

The internal temperature is too low. Stop the beeps by pressing the Start/Stop button

Start

Stop

and open the

lid. Wait 10 to 20 minutes until the appliance has reached room temperature.

The display shows “EE0” after pressing the Start/Stop button

Start

Stop

The temperature sensor is not properly connected; send the appliance for repair.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wmf KULT X - 15140011 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info