Bedienungsanleitung Worcester-Bosch GB162-80 (Seite 34 von 72) (Englisch)

697434

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Operation

6720813171 (2016/05)34

Flue Gas Test menu

Step 1 [\/2/4| Display value. Currently measured CH flow temperature in °C. Also see section 14.2, page 53.

Step 2 Activate flue gas test? Yes:  step 3

No:  step 1

Step 3 To activate the flue gas test: Press and hold the d button for more than 2 but not longer than 5 seconds

Step 4 [\/2/4] Display value. As soon as a non-flashing dot is shown in the right-hand bottom corner of the display, the

flue gas test has been activated. This means that the boiler is in heating mode at a capacity of 100 % for a

maximum of 30 minutes. The maximum CH flow temperature as set on the maximum CH flow

temperature dial of the BC10 basic controller now applies. DHW mode is possible during manual

operation.

Step 5 Press the e button.

Step 6 [p/1.6] Display value. Currently measured system pressure in bar. Also see section 14.2, page 53.

Step 7 Press the e button.

Step 8 [-/h/\] Display code: Operating phase: The boiler is in flue gas test mode. Also see section 14.3, page 54.

Step 9 Press the e button.

Step 10 [\/2/4] Display value. Currently measured CH flow temperature in °C. Also see section 14.2, page 53.

Step 11 Have 30 minutes passed or has the mains voltage been interrupted? Yes:  step 1

No:  step 12

Step 12 Deactivate flue gas test? Yes:  step 13

No:  step 5

Step 13 To deactivate the flue gas test: Press and hold the d button for more than 2 seconds until the dot disappears.  step 1

Table 10 Flue gas test

Service Mode menu

Step 1 [\/2/4| Display value. Currently measured CH flow temperature in °C. Also see section 14.2, page 53.

Step 2 Activate service mode? Yes:  step 3

No:  step 1

Step 3 To activate service mode 1st step: Press and hold the d button for more than 2 but not longer than 5 seconds

Step 4 [\/2/4] Display value. As soon as a non-flashing dot is shown in the right-hand bottom corner of the display, the

boiler is in heating mode at a capacity of 100 % for a maximum of 30 minutes.

The maximum CH flow temperature as set on the maximum CH flow temperature dial of the BC10 basic

controller (control panel) now applies.

Step 5 To activate service mode 2nd step: Simultaneously press and hold the d + e buttons for more than 2 seconds.

Step 6 [l/-/-] Display setting. Maximum capacity setting during heating mode in %. Also see section 14.3, page 54. In

this case: [l/-/-] = 100 %. Service mode has been activated. You can now temporarily lower the boiler

performance to partial load to check and if relevant set the gas/air ratio or the ionisation current.

Step 7 Press and hold the c button until the display shows [l/2/5] with a 80-kW boiler, [l/2/0] with a 65 and

100-kW boiler or [l/3/0] with a 50-kW boiler.

Step 8 [l/2/5] Display setting: with a 80-kW boiler, [l/2/0] with a 65 or 100-kW boiler and [l/3/0] with a 50-kW boiler.

Minimum capacity setting during heating mode in %. Also see section 14.3, page 54. The boiler will

reduce its performance to 25 % or 20 % respectively within a couple of seconds. The maximum CH flow

temperature set on the BC10 basic controller (control panel) applies now. Check the gas/air ratio or the

ionisation current and if necessary set the gas/air ratio according to subsection 10.2.7 or

subsection 10.2.11.

Step 9 Press the e button.

Step 10 [f/\/5| Display setting: This parameter shows the pump run-over time in minutes when heating mode has been

ended. Also see section 14.3, page 54.

Step 11 Press the e button.

Step 12 [c/\/1| Display setting: This parameter indicates the DHW mode status setting. Also see section 14.3, page 54.

Step 13 Press the e button.

Table 11 Service mode

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worcester-Bosch GB162-80 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Worcester-Bosch GB162-80

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info