Bedienungsanleitung Worcester-Bosch GB162-80 (Seite 36 von 72) (Englisch)

697434

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Operation

6720813171 (2016/05)36

Settings Menu

Step 1 [\/2/4| Display value. Currently measured CH flow temperature in °C. Also see section 14.2, page 53.

Step 2 Open the “Settings” menu? Yes:  step 3

No:  step 1

Step 3 To open the “Settings” menu: Press and hold the d + e buttons for more than 2 seconds

Step 4 [l/-/-] Display setting. As soon as the display shows [l/-/-], the “Settings” menu is open. You can set the boiler

performance using the first parameter shown on the display. Also see section 14.3, page 54.

Step 5 Adjust boiler performance? Yes:  step 7

No:  step 6

Step 6 Lower: Decrease the target boiler output with the c button. The minimum setting is [l/2/5] = 25 % with an 80-kW

boiler, [l/2/0] = 20 % with a 65 or 100-kW boiler and [l/3/0] = 30 % with a 50-kW boiler.

Higher: Increase the target boiler output with the d button. The maximum setting is [l/-/-] = 100 %.

This is equal to the factory setting.

Step 7 Press the e button.

Step 8 [f/\/5| Display setting: Set the second parameter as soon as the display shows [f/\/5|.

This parameter shows the target pump run-over time in minutes after heating operation has ended.

Also see section 14.3, page 54.

Note: Do not set a pump run-over time of less than [f/\/5| (= 5 minutes).

Step 9 Set the pump run-over time after heating operation has ended? Yes:  step 10

No:  step 11

Step 10 Lower: Decrease the target pump run-over time after the end of heating operation with the c button.

The minimum setting is [f/\/0| = 0 minutes. The factory default setting is 5 minutes.

Caution: Do not set the target pump run-over time after the end of heating operation to less than 5 minutes.

Higher: Increase the target pump run-over time after the end of heating operation with the d button.

The maximum setting is [f/6/0| = 60 minutes or [f/1/d| = 24 hours.

Step 11 Press the e button.

Step 12 [c/\/1| Display setting. Set the third parameter as soon as the display shows [c/\/1|. This parameter indicates

the DHW mode status setting. This enables DHW mode to be switched off or on. This setting has priority

over other DHW mode settings, such as those made on the room thermostat. Also see section 14.3,

page 54.

Step 13 Set the DHW mode status? Yes:  step 14

No:  step 15

Step 14 Set the DHW mode target status with the c or d buttons. [c/\/1| means “On”, [c/\/0| means “Off”.

Please note: Setting [c/\/0| also switches off the hot water cylinder frost protection.

Step 15 Have at least 5 seconds passed without a button being pressed and/or has the mains voltage been interrupted? Yes:  step 17

No:  step 16

Step 16 Press the e button.

Step 17 [\/2/4| Display value. Any adjustments that you have made have been confirmed.  step 1

Table 13 Settings

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worcester-Bosch GB162-80 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Worcester-Bosch GB162-80

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info