Bedienungsanleitung Worcester-Bosch GB162-80 (Seite 35 von 72) (Englisch)

697434

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Operation

6720813171 (2016/05) 35

Step 14 [\/2/4| Display value. Currently measured CH flow temperature in °C. Also see section 14.3, page 54.

Step 15 Press the e button.

Step 16 [p/1.6| Display value. Currently measured system pressure in bar. Also see section 14.3, page 54.

Step 17 Press the e button.

Step 18 [-/h/\| Display code: Operating phase: The boiler is in service mode. Also see section 14.3, page 54.

Step 19 Press the e button.

Step 20 [\/2/4| Display value. Currently measured CH flow temperature in °C. Also see section 14.3, page 54.

Step 21 Have 30 minutes passed or has the mains voltage been interrupted? Yes:  step 22

No:  step 23

Step 22 Service mode is deactivated.  step 25

Step 23 Deactivate service mode? Yes:  step 24

No:  step 15

Step 24 To deactivate the service mode: Press and hold the d button for more than 2 seconds until the dot disappears.

Step 25 The boiler capacity drops to the preset capacity, see the “Settings” menu (table 13).  step 1

Manual operation menu

Step 1 [\/2/4| Display value. Currently measured CH (boiler) flow temperature in °C. Also see section 14.2, page 53.

Step 2 Activate manual operation? Yes:  step 3

No:  step 1

Step 3 To activate manual operation: Press and hold the d button for more than 5 seconds.

Step 4 [//2/4} Display code: Operating phase: As soon as a flashing dot is shown in the right-hand bottom corner of the

display, manual operation is active. This means that the boiler is permanently in heating mode. The

maximum CH flow temperature as set on the maximum CH flow temperature dial of the BC10 basic

controller (control panel) now applies. The “Heat request” LED lights up. DHW mode is possible during

manual operation.

Step 5 Press the e button.

Step 6 [p/1.6} Display value. Currently measured system pressure in bar. Also see section 14.2, page 53.

Step 7 Press the e button.

Step 8 [-/h//} Display code: Operating phase: Also see section 14.3, page 54. The boiler is in manual operation mode.

This means that the boiler is in heating mode while there is no heat request from the controller. During

manual operation the “Settings” menu (table 13 from step 3) can be used to temporarily change the

target boiler performance.

Note: If the boiler performance has been changed temporarily, this must be set again after ending

manual operation, according to the “Settings” menu (table 13, page 36).

Step 9 Press the e button.

Step 10 [//2/4} Display value. Currently measured CH flow temperature in °C. Also see section 14.2, page 53.

Step 11 Has there been a power failure? Yes:  step 1

No:  step 12

Step 12 Deactivate manual operation? Yes:  step 13

No:  step 5

Step 13 To deactivate manual operation: Press and hold the d button for more than 2 seconds until the dot disappears.  step 1

Table 12 Manual operation

Service Mode menu

Table 11 Service mode

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worcester-Bosch GB162-80 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Worcester-Bosch GB162-80

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info