Bedienungsanleitung Workzone EP2800i (Seite 14 von 21) (Englisch)

724636

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

Digital Inverter Generator with Pure Sine Wave

AFTER SALES SUPPORT

e-mail: help@powertoolsupport.com

1800 909 909

MODEL: №. EP2800i • 09/2018 • 62007

(toll free)

AFTER SALES SUPPORT

(toll free)

Digital Inverter Generator with Pure Sine Wave

e-mail: help@powertoolsupport.com1800 909 909

MODEL: №. EP2800i • 09/2018 • 62007

24 25

Normal procedure for Stopping the Engine

(Full shut down and Store)

1.  Turn “OFF” the 240Va.c Outlet Power On/O switch (1) by pushing the

switch to the right hand side. (Fig U).

2. Remove any appliances connected to either of the 2 outlets (Fig K).

3. Allow the engine to slow down and idle for approx 15-30 seconds.

4. Press the engine On/O switch (2) to the “OFF” position as indicated

by an “O” (Fig. V). The unit will stop running .

5.  Turn the fuel lever / tap (23) anti clockwise to the “OFF” position (Fig. W)

Overload procedure for restarting and resetting the engine

1. Turn “OFF” the 240Va.c Outlet Power On/O switch (1) by pushing the

switch to the right hand side. (Fig U).

2. Allow the engine to slow down and idle for approximately 15-30 seconds.

Remove any appliances connected to either of the 2 AC sockets.

3. Press the engine On/O switch (2) to the “OFF” position as indicated by an

“O”(Fig. X). The unit will stop

running and is shut down.

Now follow the normal starting

procedure to restart the generator.

WARNING: All appliances are rated dierently. This generator will work

only with Australian approved rated appliances with an input voltage of

220-240Va.c (Fig T). Check your appliances meet this requirement on its

rating label before using them. In simple terms if you cant use the product

in your home you denitely cannot use it on this generator.

Overload condition ( Where the appliances want more

power then the generator can provide)

Once operating, If the AC side of the generator becomes overloaded , the

red load status indicator (5) LED will illuminate. The generator will continue

to supply 240Va.c output for a very short time, but if the load is not reduced,

the 240V supply will be automatically shut down. To reduce load rstly

you can stop using one appliance and turn it o , see if that recties the

problem. If not refer to page 15 on loading’s and how they work. If this does

NOT solve your problem, or you do not reduce load fast enough, the output

of the generator will be automatically shut down, and the petrol motor

will continue to run. You will now need to reset the overload condition by

shutting down the petrol motor (Fig S), and thus restart the engine after the

load being applied to the generator has been reduced. Refer to the Overload

procedure for re-starting and re-setting the engine. Always connect the

largest appliance you want to run rst allowing it time to draw current to

start . After 20-30 seconds connect the second appliance.

Operation Operation

OFF

V.U. W.

OFF

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Workzone EP2800i Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info