Bedienungsanleitung Workzone S1B-DW01 (Seite 11 von 15) (Englisch)

724638

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

220W 3-in-1 Multi Purpose Sander

AFTER SALES SUPPORT

e-mail: help@powertoolsupport.com

1800 909 909

MODEL No.: S1B-DW01-220W • 09/2018 • 61865

(toll free)

AFTER SALES SUPPORT

(toll free)

220W 3-in-1 Multi Purpose Sander

e-mail: help@powertoolsupport.com1800 909 909

MODEL No.: S1B-DW01-220W • 09/2018 • 61865

18 19

Operation Operation

Operation

NOTE: It is recommended that the sander always be supplied with a 240V

50Hz supply via a residual current device with a rated residual current of

30mA or less.

CAUTION! Ensure that the appliance is switched o before connecting it to

the mains power.

NOTE: For the triangular sander plate (11), and the rectangle sander plate

(9), always switch the sander on before making contact with the material to

be sanded, then apply it to the workpiece.

For the round random orbital sander plate (13), sit the sanding pad on the

workpiece and with you the operator holding the sander rmly, then start

the sander.

There is no automatic braking system on this sander and the disc will spin at

high speed if the work piece is not in contact with

the sander.

WARNING: Do not lift the sander o the workpiece

with the round random orbital sander plate (13)

in operation. Turn o the sander and then lift the

sander o the work piece when the sander comes

to a complete stand still. Failure to do the above

with the round random orbital sander plate (13)

can result in damage to the work piece surface

(spinning scratch marks).

Switching on and o

Plug in the socket to the mains power and turn on.

To turn the sander on, move / slide the ON/OFF

switch (1) towards the front of the sander to the

ON position as indicated by an “I” (Fig Q).

To turn the power of the sander o, move / slide

the ON/OFF switch (1) towards the back of the

sander to the OFF position as indicated by an “O”

(Fig R).

Setting the oscillating speed

You can set the desired oscillating speed using the

speed selector (14) as required. The required speed

depends on the material being processed and

can be determined through practice tests. There are 5 speeds + MAX for

the oscillation speed, 1 being the lowest speed, and MAX being the fastest

speed. It is recommended to start on the lowest speed and increase the

speed as the speed of the sander suits the work piece being

worked on (Fig S).

Working procedures / Operating Tips

• Do NOT sand asbestos material in ANY form.

• Always wear a dust mask, hearing protection and safety eye protection

during sanding procedures.

• Grip the rear of the handle in one hand and push down on the front of

the handle with the other hand. Take care to hold the sanding surface

parallel to the work. Do not press down heavily. This will slow down and

damage the motor. Apply enough pressure to allow the sander to do the

work.

• Switch the appliance on before applying it to the workpiece for the

triangular sander plate (11), and the rectangle sander plate (9) bases. For

the use of the round random orbital sander plate (13) for random orbiting

sanding, starting the sander and stopping the sander should be done

whilst holding the sander rmly and starting the sander with the round

sanding pad on the work piece.

NOTE: if the sanding pad is not on the workpiece for stating or stopping,

the sanding disc can rotate at VERY high speeds and mark the workpiece.

• Apply minimal pressure when working. Work at a constant speed.

• Change the sanding sheets regularly.

• Adjust the speed to suit the sanding application.

• Never sand dierent materials (such as wood and then metal) using the

same sanding sheet. Optimum sanding results can only be achieved by

using clean sanding sheets.

• Clean the sanding sheet every once in a while using a vacuum cleaner.

• Sand hard-to-reach places with the front or side edge of the sanding

sheet on the sander plate.

• Run the sander in parallel and overlapping sanding motions over the

workpiece.

• After completing the task, lift the appliance from the workpiece and then

switch it o when using the rectangle sander plate (9) and triangular

sander plate (11). For the round random orbital sander plate (13) use,

turn o the sander while the sandpaper is still on the workpiece.

• Check and empty the dust collection box (6) at regular intervals.

MAX

SPEED

LOW

SPEED

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Workzone S1B-DW01 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info