Bedienungsanleitung Yamaha CDRS1000 (Seite 17 von 38) (Englisch)

18187

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

E-14

RECORDING FUNCTIONS

English

NATURAL SOUND CD RECORDER CDR-S1000

POWER

FINALIZE ERASE DISPLAY

TRACK NO.

EFFECT

REC MODE

OPEN/CLOSE

CD DIRECT

REC

INPUT

PHONES

REC LEVEL

LEVEL

DIGITAL/ANALOG

MIN MAX

010

OPTICAL

COAXIAL ANALOG

REC

MUTE

EFFECT

FINALIZE

STOP PAUSE PLAY

SKIP

ERASE REC

REC MUTE

123

456

789

+10

INDEX

REPEAT RANDOM CLEAR PROG

REC MODE

TRACK NO.

WRITE

DIMMER DISPLAY

OPEN/

Synchronized recording

of ALL tracks

This is a recording mode suitable for recording all of the

material from a single audio source such as a CD, MD,

cassette, or LP. Track markers are automatically placed

between the tracks being recorded.

CD-R

CD TOTAL

REMAIN

PROG

RNDM

REPEAT

SINGLE

EFFECT

REC

ALL

AUTO SYNC

TOC

32 44 48.1

–

60 30 10 6 4 2 1 0 OVER00

––– ––––

INPUTREC MODE

REC MODE

CD-R

CD TOTAL

REMAIN

PROG

RNDM

REPEAT

SINGLE

EFFECT

REC

ALL

AUTO SYNC

TOC

X2 X4

32 44 48.1

–

60 30 10 6 4 2 1 0 OVER00

––– ––––

REC

4 Adjust the recording level as described on page 17.

• The recording level of digital and analog sources

can be adjusted.

• Start playing the source to set the recording level.

When the recording level is set, stop playback of

the source component.

• The recording level cannot be changed when the

CD DIRECT function is on.

5 Ensure that the source is in pause or stop mode, as

synchronized recording cannot be started if the

source is playing.

6 Press REC MODE twice.

• The ALL and SYNC indicators light in the display.

7 Start playing the source.

• The unit starts recording automatically when it

detects an audio signal.

• When making a digital recording, a new track

marker is placed each time a new track begins on

the source component.

• Depending on the source component, a new track

marker may not always be placed correctly. When

this occurs, use the manual track marking function.

• When making an analog recording, spaces of

silence are interpreted as track separations, and a

new track marker is automatically placed when a

new audio signal is detected. The silence should be

about 4 seconds long. Automatic track marking

may not be performed properly if the recording

source has excessive noise or contains a lot of low

level sounds. In this case, we recommend manual

recording as described on page 16.

• Once the unit has recorded 20 seconds of

continuous silence, recording ends and “Wait”

blinks in the display while information is being

written to the PMA (Program Memory Area). After

this is complete, the unit is put in the stop mode.

• When making a recording using the program

playback function of the source component, make

sure that the space between each track is under 10

seconds.

When you are finished recording, follow the

finalization procedure described on page 20.

1 Load a CD-R or CD-RW disc containing space for

recording.

• To ensure proper recording, make sure that you

have more than enough space on the disc.

2 Press REC.

• This unit enters record pause mode.

3 Set INPUT on the front panel to the appropriate input

to be used for recording.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CDRS1000 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CDRS1000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info