Bedienungsanleitung Yamaha CP40 STAGE (Seite 32 von 60) (Englisch)

588665

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

32 CP4 STAGE/CP40 STAGE Owner’s Manual

Quick Start Guide

5 Move the cursor (R) to Preset using the [r]

button, and select a preset* for the effect type

from Step 4 using the Data Dial. (*: Each

preset configures all parameters to suit a

specific need.)

NOTE While each preset configures all parameters to suit a

specific need, you can adjust these parameters if

necessary. To do so, press the [d] button to move to the

screen’s other panes.

6 When you have finished setting the chorus

effect, press the [EXIT] button.

The Common Edit menu will again be displayed.

7 Use the [d] button to select 02: Reverb Effect,

and then press the [ENTER] button.

The Reverb Effect screen will be displayed.

8 Use the Data Dial to change the reverb effect

type.

9 Use the [d] button to move to the screen’s

next pane and edit the parameters for the

effect type from Step 8 using the [l] and [r]

buttons and the Data Dial.

10 Using the [SLIDER FUNCTION] button and

the Part sliders, adjust the chorus send

level (CHORUS) and the reverb send level

(REVERB). (Refer to Part sliders (page 28)

for details on how to do so.)

The degree to which chorus and reverb are applied

to the affected Parts will change.

Setting insertion effects

Insertion effect settings can be configured for each of a

Performance’s Parts. Two are available for use in a

Performance, each containing two independent effects,

A and B. As an example of setting parameters in the

Performance Part Edit area, the following procedure

describes how to configure these effects for one of the

current Performance’s Parts.

1 Ensure that the Part for which you wish to

configure insertion effects is turned on (i.e.,

its Part button is lit).

If necessary, turn on the Part by pressing its Part

button.

2 Select the Part by pressing its Part button

with the [PART SELECT] button held down.

NOTE

• You can also select the Part to edit after displaying the Edit

menu in the following step.

• On the CP40 STAGE, pressing either the [LAYER] or [SPLIT]

button essentially selects the same Part.

Common Ctg T

Chorus Eff CHO SPX

ype Preset E

Cho R Slow D

Effect preset

EDIT Common

D01:Chorus Effect

Common

Reverb Eff

Type E

RWoodRoom D

Effect type

Common

Reverb Eff

RevTime HPF E

R 2.0s 20Hz U

Effect parameter

Tip

Edit symbol for Performances

Whenever you edit any of a Performance’s

parameters, the

E (Edit) symbol will be displayed at

the top-right of the screen. The purpose of this symbol

is to remind you that edits have been made but not yet

stored. All edits made to the current Performance can

be stored using the Store Performance function

(page 34). Once stored, the Edit symbol will

disappear.

Common Ctg T

Chorus Eff CHOR G

ype Preset E

Cho Basic D

Hold

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CP40 STAGE Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CP40 STAGE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info