Bedienungsanleitung Yamaha CP40 STAGE (Seite 36 von 60) (Englisch)

588665

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

36 CP4 STAGE/CP40 STAGE Owner’s Manual

Quick Start Guide

6 Press the [R] (Play) button.

The stage piano will start to record. During recording,

the light above the [R] (Play) button will turn on and

the light above the [I] (Record) button will stop

flashing and stay lit.

The following screen will be displayed while

recording.

NOTE Regardless of the screen currently displayed, the

[I] (Record) button can be pressed at any time to

begin recording when the stage piano is in Recording

Standby mode. In such a case, you can return to the

Audio Recording screen by pressing the [I](Record)

button once again after recording has started.

7 To stop or pause recording, press the

[J] (Stop) button.

When recording is ended normally in this way, the

Audio Playback screen will be displayed. On this

screen, the recorded audio file will be automatically

selected for playback.

NOTE Recording will end automatically when the length of the

recorded file exceeds 74 minutes.

Playing Audio Files

As described below, your stage piano can play audio

(Wave) files from a USB flash-memory device, regardless

of whether they have been created by the instrument

itself or come from another source.

1 Plug the USB flash-memory device

containing the audio file to be played into the

[TO DEVICE] USB terminal on the rear panel.

NOTE

• Audio files to be played using the stage piano must be

located in the root directory* of the USB flash-memory device.

(*: The directory initially displayed when you open the USB

flash-memory device on a computer or the like.)

• Your stage piano only supports the playback of 44.1-kHz,

16-bit, stereo audio files in .WAV format.

2 Press the [J] (Stop) button.

The first pane of the Audio Playback screen will be

displayed.

3 Ensure that the cursor (R) is located at the

File parameter, and then select the audio file

(.WAV) you wish to play using the [-1/NO] and

[+1/YES] buttons or the Data Dial.

4 If necessary, adjust the playback volume for

audio files. Move the cursor (R) to the

Volume parameter using the [r] button, and

then change the setting using the [-1/NO] and

[+1/YES] buttons or the Data Dial.

NOTICE

Audio files from a source other than your stage piano

may be extremely loud. Before starting playback,

therefore, you should always set the Volume parameter

to “0”. You can then raise the volume slowly to a suitable

level while playing the file in Step 5 below.

NOTE

• When playing audio files recorded using your stage piano, set

the Volume parameter to “127” in order to have them play

back at the same volume as when recorded.

• The Volume parameter can also be set on the General screen

from the Utility area.

AUDIO Re

REC

cording...

00:05

Time elapsed since start of recording

AUDIO

PLAY 00:00

File Volume

RWAV002}{ 100D

AUDIO

PLAY 00:00

File Volume

RWAV001}{ 100 D

File name

AUDIO

PLAY 00:00

File Volume

WAV001}{ R127 D

Audio-file playback position (time display)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CP40 STAGE Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CP40 STAGE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info