Bedienungsanleitung Yamaha CP40 STAGE (Seite 37 von 60) (Englisch)

588665

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

CP4 STAGE/CP40 STAGE Owner’s Manual 37

Quick Start Guide

5 Press the [R] (Play) button.

The selected audio file will start to play. During

playback, the light above the [R] (Play) button will

turn on.

6 To stop or pause playback, press the

[J] (Stop) button.

Playback of the audio file will stop.

Renaming an audio file

As described below, you can rename audio files (.WAV)

created by the stage piano or from another source on the

Audio Playback screen.

1 Carry out Steps 1 to 3 from Playing Audio

Files to select the file you wish to rename.

2 Use the [d] button to move to the screen’s

second pane.

3 Move the cursor (R) to Rename using the

[r] button, and then press the [ENTER]

button.

4 Change the name of the file as required, and

then press the [ENTER] button.

For details on how to set a name, refer to Entering text

(page 20) from the Basic Operations & Display

Content section. The following confirmation message

will be displayed before a file is renamed.

Press the [-1/NO] button if you do not wish to

proceed.

5 Press the [+1/YES] button.

The file will be renamed.

Deleting an audio file

As described below, you can delete an audio file (.WAV)

from the connected USB flash-memory device on the

Audio Playback screen.

1 Carry out Steps 1 to 3 from Playing Audio

Files to select the file you wish to delete.

2 Use the [d] button to move to the screen’s

third pane.

Tip

Starting and stopping audio playback using a

foot switch

With an FC4 or FC5 Foot Switch connected via the

[ASSIGNABLE] FOOT SWITCH jack, you can make

the following setting in order to start and stop

playback of audio files using the foot switch.

Press [UTILITY]; select 03: Controller; press [ENTER];

set FS (Foot Switch Control Number) to “98 (Play/

Stop)”.

Tip

Using the Key-on Start function

As described below, your stage piano’s Key-on Start

function can be used to start recording or playback of

an audio file automatically when you play the

keyboard.

1 Carry out Steps 1 to 5 from Recording Your

Playing as Audio or Steps 1 to 4 from

Playing Audio Files.

2 Hold down the [J] (Stop) button and press

the [R] (Play) button.

The light above the [R] (Play) button will start to

flash to indicate that Key-on Start is active. (If you

are preparing to record, the light above the [I]

(Record) button will also be flashing at this time.)

NOTE Key-on Start can be deactivated by pressing the

[J] (Stop) button once again.

3 Play any key.

Playback or recording will start automatically.

NOTE

• No precount will be played when starting recording using

the Key-on Start function, even if a value other than “off”

was set for the PreCount parameter in Step 5 of Recording

Your Playing as Audio.

• Certain screen operations will cause Key-on Start to be

deactivated while on standby for a key to be played.

AUDIO

PLAY 01:15

File Volume

RWAV001}{ 127 D

AUDIO

PLAY 00:00

File Rename

RWAV001}{ [ENTER] W

AUDIO

Rename

Name

[WAV001}{]

Are you

[NO]

sure?

/[YES]

AUDIO

PLAY 00:00

File Delete

RWAV001}{ [ENTER] U

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha CP40 STAGE Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha CP40 STAGE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info