Sampling is a powerful function that lets you bring your own recorded sounds – your voice, an instrument, rhythms, special
sound effects, etc. – into the system of this synthesizer, and play those sounds just like any other voices. These sounds, the
audio data you capture with the Sampling function, are referred to as “Samples.”
The data you create by Sampling differs depending on which mode you enter the Sampling mode from — the Voice/
Performance mode or the Song/Pattern mode. In this section, we’ll describe how to use the Sampling function from the Voice/
Performance mode in creating a User Voice.
nSee page 173 for instructions on using the Sampling function in the Song mode/Pattern mode.
In order to use the Sampling function, DIMM modules must be installed to the instrument. For details on installing DIMMs, see page 289.
Depending on the size of the audio (sample) data obtained via the Sampling function, you may not be able to save all of the desired data to a SmartMedia
card (maximum capacity: 128MB). For this reason, we recommend using a large-capacity USB storage device for your Sampling data.
Sampling your voice with a microphone and creating a Normal Voice
Follow steps #1 - 8 on page 72.
Type: sample
Source:A/D
Next:off
Mono/Stereo:L mono
Frequency:44.1k
For details about each parameter, see page 251.
nIf the Voice parameter above is set to “off,” you won’t be able to play
the sampled sound as a Voice after completing this operation.
However, you can call up the sampled sound by selecting a
Waveform. For details on how to select a Waveform, see .
1Connect a microphone to the instrument.
2Press the [INTEGRATED SAMPLING] button in
the Voice mode or Performance mode to enter
the Sampling mode.
3Press the [F2] SOURCE button to call up the
display for setting the Sampling Source, then set
the parameters as shown below.
VOICE
SONG
PERFORMMASTER
PATTERNFILE
MODE
SEQUENCER
INTEGRATED
SAMPLINGMIXINGUTILITY
DEMO
4Press the [F1] DEST button to call up the display
for setting the Sampling Destination, then set the
parameters as described below.
WaveformDetermines the Waveform number. Select a number
which has no data ([--- : -----------] is indicated). For
details about the Waveform, see page 173.
KeybankHere, set this parameter to “C3.” After the Sampling is
completed, you can hear the sampled sound by
pressing the note set here. For details about the
Keybank, see page 173.
PartThis is available when entering the Sampling mode
from the Performance mode. This parameter
determines the Performance Part to which the Voice
(below) created by sampling is assigned.
VoiceSet the Bank to “USR1” or “USR2” (one of the User
Normal Voice Banks), then select a User Normal Voice
Number. After the Sampling is completed, you can hear
the created Voice by selecting the Voice number set
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Yamaha MOTIF ES7 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.