Bedienungsanleitung Yamaha MOTIF ES7 (Seite 95 von 300) (Englisch)

571272

Zoom out

Zoom in

Vorherige Seite

1/300

Nächste Seite

Quick Guide — Advanced Course

Creating a Voice by using the Sampling function

Owner’s Manual

●Setting the Conﬁrm function

When the [F2] CONFM (Conﬁrm function) is turned on ( is

indicated), you can easily listen back to your just-recorded

sample and conveniently re-record it if you’re not satisﬁed

with the results. Here, set the [F2] CONFM button on.

●Setting the Trigger mode

The Trigger mode lets you determine how the Sampling

actually starts. For example, you can start the Sampling

simply by pressing the button or when the Song/Pattern

playback reaches a speciﬁed point. Here, set the TrggrMode

(Trigger mode) to “level” which lets you start sampling as

soon as the microphone level exceeds the speciﬁed Trigger

Level.

●Setting the Trigger Level

When the Trigger mode is set to “level,” you’ll also need to set

the Trigger Level. This determines when sampling actually

starts, depending on the level of the input signal (in this case,

your voice). As you sing into the microphone, notice the

movement of the level meter (bar), and when the bar crosses

the Trigger Level arrow. If necessary, select the Trigger Level

value and use the data dial to change it, moving the arrow as

low or as high as needed.

Doing this puts sample recording on standby, waiting for an

input signal that exceeds the Trigger level.

Sing into the microphone. (You may want to match the pitch

of your voice to the note C3, set in step #4 above.) The

sampling actually starts as soon as the an input signal

exceeding the speciﬁed trigger level is received.

Press the [F3] AUDITION button to hear the sampled sound.

If you’re not satisﬁed with the results and you wish to try

again, press the [F4] CANCEL button to return to the

Sampling Standby display and try sampling from step #5

again. If you are satisﬁed with the results, press the [F5] OK

button to store the sampled sound as a “sample” and return

to the [F1] DEST or [F2] SOURCE display.

Keep in mind that if the Conﬁrm function is turned off in step

#5 above, the display shown above will not appear when

stopping sampling. Instead, stopping sampling returns

directly to the [F1] DEST or [F2] SOURCE display.

5Press the [F6] REC button to call up the

Sampling Record display (Sampling Standby

status), then set the parameters as required.

Turn the Conﬁrm

function on or off

Indicates Sampling

Standby status.

Trigger Level

You can change the

Keybank (set in step

#4) also in this display.

Trigger Level

Indicates Sampling

Standby status.

The section of the bar exceeding

the Trigger Level becomes black.

6Press the [F6] REC button again to enable

Sampling Trigger Waiting.

7Sing into the microphone to start sampling.

8Press the [F6] STOP button to stop sampling,

then check the results.

Indicates that sample recording is waiting

for a signal of an appropriate level.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MOTIF ES7 Seite 95

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MOTIF ES7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info