The Song Job mode contains a comprehensive set of editing tools and data transform functions you can use to change the sound of the Song.
It also includes a variety of convenient operations, such as copying or erasing data.
After setting parameters as required from the selected display, press the [ENTER] button to execute the Job.
An “Executing...” message is shown when it takes a short amount of time to execute the Job. Never attempt to turn off the power while an “Executing...”
message is shown. Turning the power off in this state results in loss of all user data.
ControlChangeThese events control the sound and certain response characteristics of the voice, and are usually generated/
recorded by moving a controller (such as a modulation wheel, knob, slider or foot controller).
FCTRL NO (Control Number)Determines the Control Change number.
Settings:000 ~ 127
nFor details on the specific functions assigned to each of the numbers, see page 182.
FDATASee page 182.
Settings:000 ~ 127
Ch.AfterTouch
(Channel After Touch)This event is generated when pressure is applied to a key after the note is played.
FDATAThis represents the amount of pressure applied to the key.
Settings:000 ~127
PolyAfterTouch
(Polyphonic Aftertouch)This event is generated when pressure is applied to a key after the note is played. Unlike Channel Aftertouch above,
this is recorded and applied independently for each key pressed.
FNOTE (Note name)Determines the key to which aftertouch is applied.
Settings:C -2 ~ G8
FDATAThis represents the amount of pressure applied to the key.
Settings:000 ~ 127
RPN
(Registered Parameter Number)This event changes parameter values for each tone generator Part. This event is used to set Part settings such as
Pitch Bend Sensitivity or Tuning.
FMSB-LSBSee page 183.
Settings:000 ~ 127
FDATA (Data Entry MSB-LSB)See page 182.
Settings:000 ~ 127, ***
nNormally three types of control change data are sent: RPN MSB (101), RPN LSB (100), and Data Entry MSB (6). In this synthesizer, Data Entry LSB (38) is added to this and
the resulting group of control change events is handled as one in this display.
NRPN (Non Registered
Parameter Number)These events are used to change the parameter values for each tone generator Part. They can be is used to edit
sounds via MIDI, allowing you to edit filter or EG settings, or adjust the pitch or level for each instrument of a drum
voice.
FMSB-LSBSee page 183.
Settings:000 ~ 127
FDATA (Data Entry MSB-LSB)See page 182.
Settings:000 ~ 127, ***
nNormally three types of control change data are sent: NRPN MSB (99), NRPN LSB (98), and Data Entry MSB (6). In this synthesizer, this group of control change events is
handled as one in this display. For a complete list of the available RPN and NRPN numbers and their corresponding controls, refer to the MIDI Data Format in the separate
Data List booklet.
Exclusive (System Exclusive)A type of MIDI message used to exchange data unique to a specific model or type of device.
Unlike other MIDI events, these events differ depending on the manufacturer/device, and are incompatible among
different devices.
FDATA (HEX)See page 184.
Settings:00 ~7F, F7 (Data must be entered in hexadecimal format.)
Song Job mode[SONG] → Song selection → [JOB]
[F1] UNDO/REDO
The Undo Job cancels the changes you made in your most recent recording session, editing session, or Job, restoring the data to its previous state. This allows
you to recover from accidental data loss. Redo is available only after using Undo, and lets you restore the changes you made before undoing them.
Undo/Redo does not work with Sample Voice and Mixing Voice operations.
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Yamaha MOTIF ES7 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.