Bedienungsanleitung Yamaha MOTIF ES7 (Seite 254 von 300) (Englisch)

571272

254

Zoom out

Zoom in

Vorherige Seite

1/300

Nächste Seite

Reference Sampling Mode

Sampling Record mode When entering the Sampling mode from the Song mode/Pattern mode

254 Owner’s Manual

WAITING (Trigger Waiting or

Punch-in Waiting)

When Trigger Mode is set to “level” in the Sampling Standby display, press the [F6] REC button again to enter the

Trigger Waiting condition; the [F6] menu changes to “STOP.” In this condition, sampling will begin as soon as an

input signal exceeding the speciﬁed trigger level is received.

When the Trigger Mode is set to “meas” in the Sampling Standby display, press the [F6] REC button again to enter

the Punch-in Waiting condition; the [F6] menu changes to “STOP.” In this condition, sampling will begin as soon as a

song or pattern playback reaches the punch-in measure.

Before recording starts in either condition, press the [F6] STOP button or [EXIT] button to return to the Sampling

Standby display. Keep in mind that the Conﬁrm function can be tuned on or off by using the [F2] CONFM button also

in the Trigger Waiting or Punch-in Waiting condition if the Sampling type is set to other than “slice+seq.”

RECORDING During recording, press the [F6] STOP button or [EXIT] button to stop sampling.

After sampling (recording) stops:

The following menus appear when the Sampling type is set to “sample” or “sample+note” and the Conﬁrm function

is turned on.

[F3] AUDITION Pressing this lets you hear the sample obtained by recording (sampling).

[F4] CANCEL Pressing this deletes the sample obtained by recording (sampling) and return to the Sampling Standby display.

[F5] OK Pressing this stores the sample obtained by recording (sampling) to the speciﬁed destination.

TRIM/SLICE display after

sampling stops

If you’ve entered the Sampling Record mode for the Song or Pattern mode and you’ve set the sampling type to

“slice+seq,” you should set the following Slice related parameters after the Sampling stops.

Please note that the Conﬁrm function is not available in this case.

[F1] TRIM

The trim function makes it possible to specify the beginning and end points to be played back within an entire sample. You can also specify the tempo for

the range of the looped playback and determine its beat.

Start (Start Point) Determines the Start point for the sample playback.

Loop (Loop Start Point)

Determines the Top point of the loop playback (the point where the loop begins) within the range of the entire sample.

End (End Point) Determines the End point of the loop playback within the range of the entire sample.

Beat Indicates the (beat) and tempo of the range from the Loop Start Point to the End Point.

[SF1] AUDITION Press the [SF1] button to sound the recorded sample according to the settings in this display.

[SF2] LP=ST When the menu indication here is “LP=ST,” the Start (Start Point) and the Loop (Loop Start Point) will share the same

address, meaning that both of them will be changed simultaneously, even if just one of them is changed. Pressing

the [SF2] button in this condition changes the menu from “LP=ST” to “LP≠ST.” When the menu indication here is

“LP≠ST,” the Start (Start Point) and the Loop (Loop Start Point) can be changed independently. When pressing the

[SF2] button in this condition, the address value of the Start will be copied to that of the Loop, with the result that

both of them will have the same address value. The menu indication also changes from “LP≠ST” to “LP=ST.”

[SF3] SET END Pressing this calls up the display for determining the End Point, from which you can set the tempo, beat, and

measure for the sample. Press the [ENTER] button to actually set End Point. If you are satisﬁed with the results

(press [SF1] to audition the sample), press the [F6] OK button to return to the original display. Doing this stores your

edited sample to the DIMM memory. To return to the original display without changing the data, press the [F5]

CANCEL button.

[SF4] EXTRACT Delete all unnecessary sample data located ahead of the Start point and located after the End point) by pressing the

[SF4] button.

[F5] ZOOM-

[F6] ZOOM+

Press the [F5] and [F6] buttons to zoom in and out of the wave display.

[F2] SLICE

This powerful feature lets you automatically divide the recorded sample into separate “slices.” These slices are then assigned to successive notes and

arranged as sequence data.

nBefore executing the Slice operation, you’ll need to accurately adjust the length of the sample. Use the [SF1] AUDITION button in the [F1] TRIM display to loop the sample

and precisely set the Start and End points as required.

After specifying the following parameters, press the [ENTER] button. (The display prompts you for conﬁrmation.) Press the [INC/YES] button to execute the

Slice. You can hear and conﬁrm the sliced samples by pressing the [SF1] AUDITION button. If you are satisﬁed with the result of the operation, press the

[F6] OK button to store the result of the Slice operation and go back to the Sampling Setup display. If not, press the [F5] CANCEL button to go back to the

Sampling Setup display without storing the result.

Type (Slice Type) Speciﬁes how the sample is sliced, and to some extent determines the resulting sound quality. Select the type that

best suits the original phrase.

Settings: beat1~3, phrase1~4, quick

beat1~3 ...........This slice type is suited for percussive phrases such as drums or bass with a fast attack and short decay. Three

variations are provided.

phrase1~4 .......Ideal for phrases containing cymbals or other instruments with a long decay. Four variations are provided.

quick ................Regardless of the phrase content, the sample is divided at the speciﬁed note sub-divisions. The number of slices per

measure is calculated by multiplying the top number of the Meter (time signature) parameter by the bottom number of

the SubDivide parameter.

nFor helpful hints on getting the Slice Type parameter to work for different samples, see “Tips for using the Slice Types” on page

259.

Yamaha MOTIF ES7 Seite 254

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MOTIF ES7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info