Bedienungsanleitung Yamaha MOTIF ES7 (Seite 260 von 300) (Englisch)

571272

260

Zoom out

Zoom in

Vorherige Seite

1/300

Nächste Seite

Reference Utility Mode

Utility mode

260 Owner’s Manual

Utility mode

The Utility mode features a variety of important settings related to overall operation of the MOTIF ES. These settings can also be stored — simply

press the [STORE] button from any mode (with the exception of the Utility Job mode), and store the data to internal Flash ROM as system

settings (page 186). You can also save the settings to a SmartMedia/USB storage device in the File mode.

In this mode, you can set parameters that apply to the entire system of the MOTIF ES.

This mode is actually a sub-mode of the Voice/Performance/Song/Pattern mode. Press the [UTILITY] button in each mode to enter the Utility

mode and press the [EXIT] button after making settings to go back to the previous mode.

Utility mode [UTILITY]

[F1] GENERAL

[SF1] TG (Tone Generator) From this display you can make overall settings for the internal tone generator. Settings here do not affect MIDI

messages transmitted to the external MIDI instrument.

Volume Determines the overall volume of the instrument.

Settings: 0~127

NoteShift Determines the amount (in semitones) by which the pitch of all notes is shifted.

Settings: -24~0~+24

Tune Determines the ﬁne tuning (in 0.1 cent steps) of the internal tone generator’s overall sound.

Settings: -102.4~+102.3

BCCurve

(Breath Controller Curve) These four curves determine how the sound of the internal tone generator responds to use of a Breath Controller.

The setting here affects the Destination parameters when the Source is set to “BC,” both of which can be set in the

CTL SET displays ([VOICE] → [EDIT] → [COMMON] → [F4] CTL SET).

The graph shown in the display indicates the controller response curve. (The horizontal line represents the received

breath control values, while the vertical line represents the actual response of the internal tone generator.)

Settings: thru, soft, hard, wide

[SF2] KBD (Keyboard) From this display you can set the keyboard-related parameters. The settings here affect the MIDI messages

generated by playing the keyboard.

Octave Determines the amount in octaves by which the range of the keyboard is shifted up or down. This setting can be

changed also by pressing any of the [OCTAVE] buttons.

Settings: -3~0~+3

Transpose Determines the amount in semitones by which the range of the keyboard is shifted up or down.

Settings: -11~ 0 ~+11

nIf you transpose beyond the note range limits (C-2 and G8), notes in the adjacent octaves will be used. For example, a

transposed note of F9 will be changed to F8.

VelCurve (Velocity Curve) These ﬁve curves determine how the actual velocity will be generated and transmitted according to the velocity

(strength) with which you play notes on the keyboard.

The graph shown in the display indicates the velocity response curve. (The horizontal line represents the received

velocity values (strength of your playing), while the vertical line represents the actual velocity values transmitted to

the internal/external tone generators.)

Settings: norm, soft, hard, wide, ﬁxed

norm (normal) .......This linear “curve” produces one-to-one correspondence between the strength of your keyboard playing (velocity)

and the actual sound change.

soft ........................This curve provides increased response, especially for lower velocities. In other words, playing softly results in

higher response than the “norm” curve.

hard.......................This curve provides increased response, especially for higher velocities. In other words, playing hard results in

higher response than the “norm” curve.

wide ......................This setting provides opposite response curves for lower and higher velocities. It widens the apparent dynamic

range of the controller, producing less sound change in the softer range and more change in the higher range.

ﬁxed ......................This setting produces the same amount of sound change (set in Fixed Velocity below), no matter what your playing

strength.

FixedVelocity This parameter is only available if you select the “ﬁxed” Velocity Curve above. The velocity of the note you play is

ﬁxed at the value set here.

Settings: 1 ~ 127

[SF3] EF BYPS (Effect Bypass) From this display you can select the speciﬁc effect(s) to be bypassed when the [INSERTION] or [SYSTEM] button of

EFFECT BYPASS buttons is turned on.

Insertion

FInternal When this is set to on and the [INSERTION] button is turned on, the internal Insertion effect is bypassed.

FPLG-EF (Plug-in Effect) When this is set to on and the [INSERTION] button is turned on, the PLG100-VH Insertion effect is bypassed. This is

available only when the PLG100-VH has been installed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MOTIF ES7 Seite 260

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MOTIF ES7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info