Bedienungsanleitung Yamaha MOTIF XF8 (Seite 50 von 86) (Englisch)

571282

Zoom out

Zoom in

Vorherige Seite

1/86

Nächste Seite

MOTIF XF Owner’s Manual

Using the Sampling feature

Sampling in the Pattern mode

In addition to its use in the Voice and Performance modes,

the Sampling mode can also be entered from the Song and

Pattern modes. This lets you record audio (such as vocals,

electric guitar, or audio from an external device), and use it

directly on a Song/Pattern track as a Sample Voice.

In this section, you’ll learn how to record audio data (from

commercially available sample CDs, for example) to the

Pattern track, using the versatile Sampling feature. After

recording the audio, you can slice it into individual Samples,

which can then be played back at any desired tempo—

without compromising the sound or introducing pitch

changes. These step-by-step instructions assume that the

recorded audio data is a one-measure drum pattern in 4/4

time.

Sampling procedure

Connect the audio equipment (CD player) to the

MOTIF XF.

For information about how to do this, see page 47.

2 Press the [PATTERN] button to enter the Pattern

mode, then select the Pattern Number and Section.

3 Press the [INTEGRATED SAMPLING] button to

enter the Sampling mode. (The indicator lights.)

The Sampling Main display appears.

4 Press the [F6] Rec button to call up the Record

Setup display, then set each parameter as follows.

Set other parameters as necessary.

5 Press the [F6] Standby button to call up the Record

Standby display.

6 Set the Trigger Mode to “level,” and set the Trigger

Level to “1.”

7 Play back the audio source (CD player) and adjust

the audio input level with the GAIN knob on the

rear panel to set the appropriate level.

Adjust the GAIN so that the level is high enough for a clean

recording but not so high as to cause clipping or distortion.

NOTE

Please note that the input sound may be clipped or

distorted if the meter reaches maximum level.

8 Stop playback of the audio source (CD player).

9 Press the [F5] button to call up the WAITING

indicator (Trigger Standby status).

10 Start the CD player.

Since the Trigger Level is set to “1” here, sampling will

begin automatically as soon as the audio signal is input

from the CD player. In this example, record a one-measure

drum pattern from the CD.

11 Press the [F6] button to stop sampling, then stop

the CD player.

The wave of the recorded audio signal will be shown on

the display.

12 Press the [SF1] button to hear your newly

recorded sound.

Sampling Edit procedure

 Setting the End Point of the Recorded

Sample

The start point of the recorded Sample will probably be at

the correct place—the first beat of the measure—since

Sampling start was set to begin automatically with the

Trigger Level setting. However, the end point may not be at

the end of the measure as desired, since Sampling was

stopped manually. Accordingly, you may need to edit the

End Point of the recorded sample so that playback of the

recorded sample properly matches the beat timing.

Recording Type Select “slice+seq.”

Input Source Select “A/D Input.”

Mono/Stereo Select “stereo.”

Record Next Select “off.”

Frequency Select “44.1kHz.”

Track Select the track to which the Sample Voice is

assigned.

A /D INPUT

GAIN

MIN

MAX

End

Point

Te mpo

Measure

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MOTIF XF8 Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MOTIF XF8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info