Bedienungsanleitung Yamaha S30 (Seite 68 von 156) (Englisch)

586917

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

Voice Mode

■Switch

Switch the Arpeggiator on or off.

❏Settings: off, on

■Hold

Switch the Arpeggiator Hold on or off.

❏Settings: syncoff (see below), off, on

syncoff

The first time you press a key, the first note of the

arpeggiator pattern is played. From the second and

subsequent key presses, the arpeggiator note that is played

back will depend on the arpeggiator tempo and the timing

of the arpeggio pattern. For example, in the case of a 1-bar

arpeggio pattern, if the second key press falls on the third

beat of the bar, the arpeggio pattern plays back from the

third beat onward. In other words, the first key press is

used to start the arpeggio pattern and thereafter you can

use the key to “mute” or “un-mute” the pattern by,

respectively, holding it down or releasing it. This is

particularly useful when the arpeggiator is being used to

generate drum patterns.

Details about this are given on Page 38.

ARP Limit (Arpeggio Note Limit)

■Note Limit

Set the lowest and highest notes in the Arpeggiator’s

note range.

❏Settings: C-2 ~ G8 (lowest and highest set separately)

If you specify the highest note first and the lowest note

second, for example “C5 to C4,” then the note range

covered will be “C-2 to C4” and “C5 to G8.”

You can set the lowest and highest notes in the range by

pressing notes on the keyboard while holding down the

[SHIFT] key.

ARP Mode (Arpeggio Mode)

These parameters control the way in which notes are

played back by the Arpeggiator.

■Key Mode

Set how the Arpeggio is played back when keys on

the keyboard are pressed. There are 3 modes.

❏Settings:

sort:

Plays back notes in ascending order from the lowest key

pressed to the highest.

thru:

Plays back notes in the order in which the keys are pressed.

direct:

Plays back the notes exactly as you play them. If changes

to Voice parameters (such as Pan or Cutoff frequency) are

included in the Arpeggio sequence data, they will be

applied and reproduced whenever the Arpeggio plays back.

ARPíMode) Key Mode Vel Mode

C 1234 sort thru

ARPíLimit) Note Limit

C 1234 C-2 - G 8

If the Arpeggio Category is set to Ct, you will not hear

any sounds unless you select “direct” here.

With the “sort” and “thru” settings, the order in which

notes are played back will depend on the Arpeggio

sequence data.

■Vel Mode (Velocity Mode)

Set the playback velocity of the Arpeggio. There are

2 modes.

❏Settings:

original:

Preset velocities are used in the Arpeggio sequence.

thru:

Velocities of the notes you play are used in the Arpeggio

sequence.

ARP PlayEF (Arpeggio Play Effects)

You can set Play Effects for the Arpeggio. Play Effects

can be used to temporarily adjust the timing and

velocity of MIDI notes, thus affecting the groove of the

Arpeggio pattern.

■Unit

Adjust the Arpeggio playback time. For example, if

you set a value of 200%, the playback time will be

doubled and the tempo halved. Alternatively, if you

set a value of 50%, the playback time will be halved

and the tempo doubled. Normal playback time is

100%.

❏Settings: 50%, 66%, 75%, 100%, 133%, 150%, 200%

■Vel (Velocity)

Set the Velocity offset value (the strength at which

the keyboard is played). This determines how the

original Velocities are increased or decreased during

Arpeggio playback. A setting of 100% means the

original values are used. Settings below 100% will

reduce the velocity of the Arpeggio notes, whereas

settings above 100% will increase the velocities.

❏Settings: 0% ~ 200%

If the Velocity value falls below 1, it will be limited to 1.

If it exceeds 127, it will be limited to 127.

■Gate (Gate Time)

Set the Gate Time Rate value (the length of a note).

This determines how the original Gate Times are

increased or decreased during Arpeggio playback. A

setting of 100% means the original values are used.

Settings below 100% will shorten the gate times of

the Arpeggio notes, whereas settings above 100%

will lengthen them.

❏Settings: 0% ~ 200%

If the Gate Time value falls below 1, it will be limited to 1.

ARPíPlayEF) Unit Vel Gate

C 1234 50% 200% 200%

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha S30 Seite 68

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha S30

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info