Bedienungsanleitung Zelmer 13Z011 (Seite 210 von 228) (Englisch, Polnisch)

538892

210

Zoom out

Zoom in

Vorherige Seite

1/228

Nächste Seite

210

Carefully remove the brewing head unit (14). Press the protrusion (26) with your thumb (see ﬁ g. 2) and ﬁ rmly grasp the

handle (14a) with the other four ﬁ ngers and take out the brewing head unit according to the directions of the arrows in ﬁ g. 4

(ﬁ rst a gentle upward movement and next a horizontal movement). Be careful when inserting the heat unit (14) back into

place: holding the handle (14a) direct the head unit (14) on the protrusion (23) (see ﬁ g. 2), next push gently in the horizon-

tal direction to the center of the coffee maker and next vertically downwards (see arrows in ﬁ g. 5).

Fig. 4 Fig. 5

Fig. 6

The brewing unit (14) is inserted properly if the coupling of the brewing head unit axis (14g)

is on the shaft under the head unit (14h) (ﬁ g. 3). Gently close the door (15). Do not use

force, if you cannot close the door. The brewing head (14) might not be installed prop-

erly. In such a case, remove the brewing head again according to the instructions above.

Check if the brewing head unit mechanism is in the START position. This means that

the axis of symmetry of the triangle on the right side ◄ (the X line) should be be-

tween the two verticals of the two triangles on the left side ▼ ▲ (ﬁ g. 6).

If for any reason (e.g. due to cleaning) the brewing head unit is not in the START position, turn the unit axis cou-

pling (14) (ﬁ g. 6) to the right or to the left using the key (25) to set the “starting” position (ﬁ g. 6).

If the shaft inside the coffee maker (14h) is turned e.g. during cleaning, it needs to be reset properly using the

other end of the brewing unit key (25). Never turn the coupling more than half a turn. Never use force while turning

the key (25). Now try to insert the brewing head unit (14) again.

Warning: The brewing head unit (14) may be blocked if the coffee maker service door (15) is not completely open

or is not properly and completely closed.

5. Before initial use – tips

Unpack the appliance and remove all packaging materials. Never leave any plastic bags or polystyrene, etc. in the ●

reach of children as they may pose a threat to them.

Place the coffee maker on a ﬂ at surface, away from any heat or water source. Make sure there is at least 10 cm of free ●

space around the appliance and 20 cm above the appliance.

Never install the coffee maker in environments in which the temperature may fall below 3°C, because freezing water ●

may damage the pipes and elements inside the appliance. Keep the appliance away from direct sunlight and excessive

heat.

Take out the measuring spoon ● (24), the brewing head unit key (25), the ﬂ oat (3a) and the ﬂ oat plug (3b) out of the

water tank. The elements are wrapped in a plastic foil. Insert the ﬂ oat (3a) and the ﬂ oat plug inside the water tank (3).

Check if the brewing head unit (14), the dregs box (22) and the drip tray (19) together with the drip tray grill (21) are in

their proper places (ﬁ g. 7).

ATTENTION! Remove the self-adhesive transport tape from the drip tray (19) and the drip tray grill (21). ●

Rinse the water tank ● (3), wipe the bean coffee container (4) clean with a damp cloth.

Set the water hardness, following the directions in chapter ● 16.7 “Setting the Water Hardness”.

NOTE! Each coffee maker is checked in the factory before shipping using bean or ground coffee. Therefore ●

the possibility of coffee remains inside the appliance is a normal situation. It is recommended to pour out

2 ﬁ rst cups of coffee when using the coffee maker for the ﬁ rst time.

CAUTION! Never ﬁ ll the water tank (3) with hot water, mineral water or other liquids. Use only cold, fresh water. ●

The water tank (3) can be removed to ﬁ ll it with water by lifting it upwards.

Putting bean coffee or any other food products or liquids inside the ground coffee container by accident may result in ●

damage to the coffee maker.

Make sure the ● ﬂ oat (3a) is still in the left corner of the water tank (3). It is a sensor informing about the current water level.

Fill the water tank ● (3) with water before the initial use of the coffee maker (see chapter 6).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zelmer 13Z011 Seite 210

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info