Bedienungsanleitung Arcam solo movie 2 1 (Seite 6 von 30) (Englisch)

160350

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

E-6

positioning the unit

< Place Solo Movie 2.1 on a level, ﬁrm surface,

avoiding direct sunlight and sources of heat or

damp.

< Do not place Solo Movie 2.1 on top of a power

ampliﬁer or other source of heat.

< Do not place Solo Movie 2.1 in an enclosed space

such as a bookcase or closed cabinet unless there

is good provision for ventilation. Solo Movie 2.1 is

designed to run warm during normal operation.

< Do not place any other component or item on

top of Solo Movie 2.1 as this may obstruct airﬂow

around the heat-sink, causing Solo Movie 2.1 to

run hot. (The unit placed on top of Solo Movie 2.1

would become hot, too.)

< Make sure the remote-control receiver in the

centre of the front panel display is unobstructed,

otherwise this will impair the use of the remote-

control. If line-of-sight is impractical, a remote-

control repeater can be used with the rear panel

connector (see below).

< Do not place your record deck on top of this

unit. Record decks are very sensitive to the noise

generated by mains power supplies which will be

heard as a background ‘hum’ if the record deck is

too close.

Power

Solo Movie 2.1 is supplied with a moulded mains plug

already ﬁtted to the lead. Check that the plug supplied

ﬁts your supply – should you require a new mains lead,

please contact your Arcam dealer.

Push the IEC (kettle-style) plug end of the power cable

into the socket on the back of Solo Movie 2.1, making

sure that it is pushed in ﬁrmly. Plug the other end of the

cable into your mains socket and, if necessary, switch the

socket on.

Solo Movie 2.1 is ﬁtted with a power switch on the

rear panel, above the power inlet: make sure that this is

switched on.

Solo Movie 2.1 is ﬁtted with a transformer designed to

accept the mains voltage in the region that the product

was shipped to. If your mains supply voltage does not

match the speciﬁcation printed on the rear panel, or you

wish to take the unit to a region with a different mains

voltage, or the mains plug is incorrect, please contact

your Arcam dealer.

Rear panel – version with SCART

connectors and FM/DAB radio (mainly

distributed in Europe)

Rear panel – version with Composite video

connectors and FM/AM radio (mainly

distributed in U.S.A.)

installation

Interconnect cables

We recommend the use of high-quality screened cables

that are designed for the particular application. Other

cables will have different impedance characteristics

that will degrade the performance of your system (for

example, do not use cabling intended for video use to

carry audio signals). All cables should be kept as short as

is practically possible.

It is good practice when connecting your equipment to

make sure that the mains power-supply cabling is kept as

far away as possible from your audio cables. Failure to do

so may result in unwanted noise in the audio signals.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam solo movie 2 1 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Arcam solo movie 2 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info