Bedienungsanleitung Arcam solo movie 2 1 (Seite 8 von 30) (Englisch)

160350

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

E-8

video connections

To view the pictures from Solo Movie 2.1 you need to

connect one of its video outputs to your display device

(TV, monitor, projector, etc.).

Solo Movie 2.1 has three of the four video output

options described below. All versions of Solo Movie 2.1

have HDMI and Composite outputs. In addition, and

depending on the shipping region, your unit will have

either SCART or Component video connectors, to

match the connections typically used in your region. You

need only use one type of video connection from those

available; choose a type that your display device supports.

If your display device does not support any of the above

connection types, you may need to update your display

to use it with Solo Movie 2.1; in this case, please contact

your dealer for further assistance.

Video inputs

You can use other video equipment (satellite/cable

receivers, games consoles, etc.) with Solo Movie 2.1.

Connect these to the audio and video inputs of Solo

Movie 2.1. You can use any of the video inputs provided,

but the same type of connector should also be used to

connect Solo Movie 2.1 to the display device.

Solo Movie 2.1 does not convert video formats, so

if a video source is connected (for example) via the

COMPOSITE VIDEO SAT input, it is only available at the

COMPOSITE VIDEO OUT socket.

HDMI digital video

The HDMI connector offers uncompressed digital video

and audio transmission between Solo Movie 2.1 and the

display device, and provides the highest quality video

output. Generally, it is also the easiest connection type to

conﬁgure.

To use this video connection,

you’ll need a HDMI or HDMI/DVI

cable between Solo Movie 2.1

and your display device. Arcam

recommends that you use high

quality HDMI cables for the best

results.

In the Video set-up menu (see

page 18), ‘Video Resolution’

should be set to ‘Auto’. The unit will conﬁgure its video

output automatically to match the capabilities of the

attached HDMI device.

Component video

Use three 75Ω phono cables to

connect the Component Y, Pb, Pr

outputs of Solo Movie 2.1 to the Y,

Pb, Pr inputs of the display device.

Ensure that the cables are suitable

for video use and that they are

approximately the same length.

If your television is capable of accepting a progressively

scanned (de-interlaced) video signal, you may wish to

use the progressive video output from Solo Movie 2.1

for best results. If you are unsure whether your display

device can accept progressive video, please refer to its

instruction manual or consult your dealer.

Some component video interfaces are labelled differently

to the back panel of Solo Movie 2.1; check the table if the

component inputs of your display device are not labelled

‘Y, Pb, Pr’.

SCART output

The SCART connector is

common on European A/V

equipment and provides a

convenient connection method

between Solo Movie 2.1 and

display device, carrying both

video and stereo audio.

If you are using a SCART connection and you do not

wish to listen to the audio through your TV, turn the

volume down fully on your TV’s speakers, or to use the

MUTE control.

Note that the SCART output has a control signal that

switches your TV to its SCART input when Solo Movie

2.1 is turned on. It will also signal to wide-screen TVs the

correct aspect ratio (16:9 or 4:3), provided this feature is

supported by the TV.

Solo Movie

2.1

alternative alternative alternative

Y Y Y Y

Pb Cb (B–Y) U

Pr Cr (R–Y) V

Composite video

If your display device offers only a

composite input (sometimes labelled

CVBS or just ‘video’), connect this to

the COMPOSITE VIDEO OUT socket of

Solo Movie 2.1 using a 75Ω phono

cable suitable for video use. Note that

a composite video connection gives the lowest-quality

output; if your display device supports other video

connection types, we advise you use them instead.

Using two video connections

simultaneously

In some circumstances, it is possible to use two video

connections simultaneously (routing one connection to a

second room or display, for example). If you wish to do

this, please read these notes:

The Composite video and SCART outputs are

only active if HDMI is not connected (or if ‘HDMI

Resolution’ is set to ‘SD Progressive’ – see page

18). These two output types carry interlaced

output at all times.

The Component video output is only active if

HDMI is not connected (or if ‘HDMI Resolution’

is set to ‘SD Progressive’ – see page 18). It can be

set to carry either interlaced or progressive-scan

output.

The HDMI output is active only if a compatible

display is detected by the Solo Movie 2.1. It can be

set to carry either interlaced, progressive-scan or

high-deﬁnition output.

About HDMI

HDMI (High Deﬁnition Multimedia Interface) supports

both video and audio on a single digital connection

for use with DVD players, digital TV, set-top boxes, and

other AV devices. HDMI was developed to combine

the technologies of High-bandwidth Digital Content

Protection (HDCP) and the Digital Visual Interface

(DVI) in one speciﬁcation, with the addition of

transmission of digital audio information; HDCP is used

to protect digital content transmitted to DVI-compliant

displays.

HDMI has the capability to support standard

or high-deﬁnition video and stereo audio. HDMI

features include uncompressed digital video, one

connector (instead of several cables and connectors),

and communication between the AV source and AV

receivers.

Arcam solo movie 2 1 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Arcam solo movie 2 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info