Bedienungsanleitung Arcam solo movie 2 1 (Seite 7 von 30) (Englisch)

160350

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

E-7

movie 2.1

solo

English

RS232 control

Solo Movie 2.1 has an RS232 serial

connector that allows control from a PC or

similar device. This connector is also used

with rDock and rLead (see the following

section).

For details of the RS232 control protocol

used with Solo Movie 2.1, see your Arcam

dealer.

Listening with

headphones

The front-panel of Solo Movie 2.1 has a socket for

connecting headphones. To use headphones with

the unit, plug the headphones into the socket on

the left hand side of the

front panel – the main

speaker output and the

pre-amp. output are muted

automatically but Zone 2

output remains active.

This socket accepts

headphones with an

impedance rating between

Ω and 600Ω, ﬁtted with a

3.5mm stereo jack plug. The

headphone socket is always

active, except when Solo

Movie 2.1 is muted.

MENU SOURCE INFO OK

POWER

VOLUME

TAPE

�

�

Audio outputs

PRE OUT SUB: This is for connecting a Low Frequency Effects

speaker (an active subwoofer, such as Arcam’s Logo).

PRE OUT LEFT/RIGHT: If you require more power than Solo

Movie 2.1’s 50W per channel, you can connect the LEFT/

RIGHT pre amp outputs to an external power ampliﬁer.

Check that your speakers can use the extra power

before connecting them to the speaker terminals of

the external ampliﬁer. See also ‘bi-amping your front

loudspeakers’ on page 10.

ZONE 2/REC OUT: This is the output to be used for connecting to an audio recorder

or for a second room system (see page 11). It should be connected by phono–

phono (RCA) cables to the ampliﬁer in the second room. When used for a

second room, the volume can be controlled by the remote control in Zone 2 or

from the Zone 2 menu. The output level can vary with the volume control for

the second room (see page 19).

Audio inputs

Solo Movie 2.1 provides four audio inputs, allowing

connection of other audio sources, (a games console,

TV, satellite tuner, etc.). Three of these inputs are on the

rear panel, with one on the front panel. The labels above

the inputs give suggested uses, but all four inputs have

the same characteristics (all are line-level inputs) and any

suitable device may be connected to any input. (Note,

however, that the name of the input shown on the front-

panel display cannot be changed.)

To connect a device to an input on the rear of Solo

Movie 2.1, use a stereo phono cable of a suitable

length; for connection to the front-panel, the cable must

terminate in a stereo 3.5mm jack plug. Connect the

MENU SOURCE INFO OK

POWER

VOLUME

TAPE

�

�

audio output of the device to one of the inputs of Solo

Movie 2.1, making sure that the plugs are pushed in ﬁrmly.

We advise you to use high-quality interconnect cables

wherever possible to ensure the best possible sound

quality.

Connecting a record deck

Solo Movie 2.1 is not ﬁtted with a phono pre-ampliﬁer. If

you wish to connect a record deck to Solo Movie 2.1, then

you will need an external pre-ampliﬁer. Please contact your

dealer for further information and recommendations on the

best option for you.

The ‘

REMOTE’ connections are for use in second room

installations (see page 11).

12V TRIGGER – This output provides a 12V signal

whenever the unit is switched on (i.e., not off or in

clock mode). This signal can be used to switch on

compatible equipment (such as power ampliﬁers)

connected to Solo Movie 2.1.

OUT – This output carries all signals from the front-

panel remote-control receiver, plus commands

received through the two external sensor inputs

(IN LOCAL and IN ZONE 2). This can be used

to route remote-control commands to other

equipment (potentially in different locations).

For example, satellite receiver commands could

be received by Solo Movie 2.1, then routed to a

satellite receiver in a remote location using this

output connector.

IN LOCAL – This allows remote control

signals to be received by Solo

Movie 2.1 if the front panel sensor

is covered (or otherwise not ‘visible’

to the remote control). An external

sensor is used to receive the signals

from the remote control, which are

then fed to Solo Movie 2.1 (into this

input) using a suitable cable.

IN ZONE 2 – Use this connector if you are

using a second room system that has

a remote sensor. The external sensor is used to

receive the signals from the remote control, which

are then fed to Solo Movie 2.1 (into this input)

using a suitable cable.

Remote control inputs/outputs and the 12V trigger

iPod

control

Music from your iPod can be fully integrated with your

system using Arcam’s rDock or rLead. Solo Movie 2.1

takes over the control and ampliﬁcation, with iPod text

appearing on the front panel display of the unit. Full

details of connecting up and using the CR100 for remote

control are given in the rDock or rLead quick start

guide supplied with these accessory units.

audio connections

DIGITAL AUDIO OUT: This is an optical output (TOSLINK),

carrying digital audio output. This can be used for making

digital recordings using compatible recording devices (such as

MiniDisc). CD playback is at 44.1kHz; DAB radio (where ﬁtted)

plays 48kHz, DVD playback is at 48kHz or 96kHz, and DVD-A

is at up to 96kHz. Digital output from analogue inputs is at

44.1kHz. SACD discs do not provide digital output.

Digital audio inputs

Solo Movie 2.1 provides three digital audio inputs: an AUX (optical) input, and two SAT

inputs (one optical and one coaxial). If a signal is connected to both SAT inputs, the

coaxial input takes priority over the optical input.

Digital inputs take priority over analogue inputs for the same source. So if both analogue

and digital inputs are connected to the same input source, Solo Movie 2.1 will use the

digital signal.

Arcam solo movie 2 1 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Arcam solo movie 2 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info