Bedienungsanleitung Caliber MCD 770 (Seite 3 von 23) (Englisch)

497338

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

ENGLISH

STATION SELECTION

Press up or down button (20) shortly to activate automatic seek function. Press for 2

seconds until “ MANUAL” appeared on the display, the manual tuning

Mode is selected. If the buttons are not touched for more then 3 seconds it

automatic goes back to “AUTO SEEK”

AUTOSTORE AS

-Automatic Memory Storing

Press func button (10) “AS/PS” longer then three seconds , activate AS.The radio searches

for the 6 strongest stations and stores them into the preset of the currently selected band.

NOTE: Any stations that were previously stored in this memory bank are replaced by

a new station.

PRESET SCAN PS

Press func button (10) “AS/PS” for less then three seconds.The unit will pause for ten

seconds at each preset station. Press button (10) “AS/PS” again to stop scanning when

the desired station is reached.

Station store and recall

Press any one of the preset buttons (12 to 17) to recall a station which had been

stored in the memory. Press a preset button for 2 seconds, previous preset station is

overwritten by current tuned frequency.

RDS (RADIO DATA SYSTEM) OPERATIONS

The RDS data are the PI, PS,TP, PTY,TA and AF data.

PI: Program indentification code

Code for identifying program

PS: Program service name

Broadcast station name data expressed

In alphanumerically character

TP:Traffic program identification

Identification data for traffic information broadcasting station

TA:Traffic announcement identification

Identification data showing traffic information is being transmitted or not

AF:Alternative frequencies

Frequency list of broadcasting station transmitting the same program

SETTING AF MODE

Press button (3) AF for less then three seconds to select AF to be ON or OFF

Whenever AF is switched on, symbol “AF” appears on the display.

The tuner will return to Alternative Frequencies whenever the reception signals

getting worse.“ALARM” will be displayed when an emergency broadcasting is

received;meanwhile sound output level will be adjusted to the preset output level

automatically when the volume control is set at minimum.

USING PTY TO SELECT PROGRAM

The PTY function allows you to search for stations with a particular program type.

To select your program type, press the button (5) “PTY” less then three seconds.

Display will show:“pop music” or “news. Now you can select the music type or

speech type using preset keys 1 to 6 for your selection as listed table:

Preset number PTY “pop” group PTY in “news” group

1 pop m, rock m news,affairs,info

2 easy m, light m sport,educatie,drama

3 classics, other m culture, science, varied

4 jazz, country weather, finance, childeren

5 nation m, oldies social, religion, phone in

6folk m travel, leisure, document

While selecting PTY engagement, its selection is implemented by preset button as

described in notes.When PTY is selected, the radio starts to search corresponding

PTY information is detected. If corresponding PTY information is not found, normal

radio reception is resumed.After the text “NON PTY” is at the display for 5 seconds.

LISTENING TO TRAFFIC ANNOUNCEMENT (TA)

Traffic announcement can interrupt CD play or radio listening when broadcast.

Briefly press the button (4) “TA” to select the TA mode on or off.When TA mode is

on, you will hear the traffic announcement when broadcast. During traffic

announcement,you can interrupt it by short press of TA button (4).Without

switching off the TA mode. By doing so, the set will return to the previous operating

mode. Long press on TA button(4) allows ON/OFF selection of EONTA

LOCAL/EONTA DX

EONTA LOCAL will only allow traffic announcement from strong station to come through.

EONTA DX selection will allow all received announcements to interrupt CD play or

radio listening.

DUAL ZONE OPERATION

This unit is equipped with the advance feature “Dual zone”.This function is useful if

the user want to select different modes of the audio output source for Front and

Rear speakers.The details operation as follow;

ON/ OFF OPERATION

• “Off” is the default setting.

• Short press the “2-zone” button on the control pannel or remote control to switch

between Dual zone on or off.The “2-zone” icon will appear on the LCD after Dual

Zone is selected “on”.

TO SELECT FRONT/ REAR SOURCES

• Once “on” is selected, short press the “AUDIO” button repeatedly to change

between the F-zone (front) and the R-zone (rear) sources.

• If front zone “F-zone” is selected, user has 10 seconds ot navigate through different

modes by using the volume button.

ENGLISH

INTER AMPLIFIER ON/OFF (INTER AMP)

This is an option selection for users to turn the unit’s built in Amplifier system on or

off.The default is “off”, this is useful for users if an external amplifier is connected and

you don’t want audio output of the built in amplifier system.

PROGRAMMABLE TURN-ON VOLUME (VOL PGM)

This option allows selection of the volume level, the radio will automatically assume

when turning on.“Vol PGM 12” is the default setting, which will turn on the radio at

the volume level as adjust in the VOL PGM.To program a specific turn on volume

level, use the volume control button to select “Volume Level” within 5 seconds.

BEEP TONE

The beep tone feature allows the selection of an audible beep tone when a button is

pressed.“Beep tone on” is the default setting. Use the volume up/down button to

select the “Beep tone off” option.

AUDIO OPERATIONS

Press the button (8) “AUDIO” to enter the sound set up. Press button (8) “AUDIO”

momentarily to move forward to the next option.The menu can also be navigated by

using the buttons (20) Tuning Up or Tuning Down to move to the next or previous

option. Once the desired option appears on the display, adjust that option by rotating

the volume control within 5 seconds.The following options can be adjusted:

VOLUME

To increase the volume rotate the volume knob (8) clockwise, to decrease the volume

rotate the volume knob counterclockwise.

SUBWOOFER (SUBWOOFER LEVEL)

Rotate the volume knob (8) to select the desired volume level from “00” to “12”.

NOTE:The subwoofer level control will only appear in the Audio Menu if the

“Subwoofer” function is activated and a subwoofer speaker is connected.

Press button (3) “SUB-W” to activate the subwoofer function. Press again to turn off.

SUB-W LPF (SUBWOOFER LOW PASS FILTER)

Rotate the volume knob (8) to select the desired Low Pass Filter function: Flat, 80Hz,

120Hz or 160Hz.

NOTE :The subwoofer level control will only appear in the Audio Menu if the

“Subwoofer” function is activated and a subwoofer speaker is connected.

IX-BASS (IX-BASS LEVEL)

Rotate the volume knob (8) to select the desired Bass Boost function: low, mid or high.

NOTE :The iX-Bass function will only appear in the Audio Menu if the “iX-Bass”

function is activated. Press button (5) “IX-BASS” to activate the iX-Bass function.

Press again to turn off.

BASS (BASS LEVEL)

Rotate the volume know (8) to select the desired Bass level from “-6” to “+6”.

BASS-CFQ (BASS CENTER FREQUENCY)

Rotate the volume knob (8)

to select the desired Bass

center Frequency to 60Hz,

80Hz, 100Hz or 200Hz.

BASS-Q (BASS Q FACTOR)

Rotate the volume knob (8)

to select the desired Bass-Q

Factor to 2N, 1N, 1W or

2W.

MIDDLE (MIDDLE LEVEL)

Rotate the volume knob

(8) to select the desired

Middle Level from “-6” to

“+6”.

MID-CFQ (MIDDLE

CENTER FREQUENCY)

Rotate the volume knob

(8) to select the desired

Middle Range Center

frequency to 500Hz,

1KHz, 1.5KHz or 2.5KHz.

MIDDLE-Q (MIDDLE Q

FACTOR)

Rotate the volume knob

(8) to select the desired Middle-Q Factor to 2N, 1N, 1W or 2W.

TREBLE

Rotate the volume knob (8) to select the desired Treble level from “-6” to “+6”.

TRE-CFQ (TREBLE CENTER FREQUENCY)

Rotate the volume knob (8) to select the desired Treble center Frequency to 10KHz,

12.5KHz, 15KHz or 17.5KHz.

BALANCE

Rotate the volume knob (8) to adjust the Balance between the right and left speakers

from R12 (full right) to L12 (full left).

FADER

Rotate the volume knob (8) to adjust the Fader between the front and rear speakers

from R12 (full rear) to F12 (full front).

RADIO OPERATIONS

BAND SELECTION

At tuner mode, press button (19) “BAND” shortly to select the desired band.The

reception band will change in the following order: FM1, FM2, FM3 and MW

Level

(dB)

Frequency (Hz

)

100

1.10

Level

(dB)

Frequency (Hz)

15.0

12.5

10.0

7.5

2.5

0.0

5.0

10.0 100.0 1.0K 10.0K

MCD 770 manual.qxd 22-10-2007 09:08 Pagina 4

Caliber MCD 770 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Caliber MCD 770

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info